What to do if my Panasonic SC-AK14 Stereo System cannot be operated with the remote control?
If the system cannot be operated with the remote control, check the batteries. If the batteries are installed in the reverse polarity, re-insert them in the correct polarity. If the batteries are run-down, replace them with new ones.
What to do if the left and right sounds are reversed on my Panasonic SC-AK14 Stereo System?
If the left and right sounds are reversed, it means the left and right connections to the speakers are reversed. Connect the speaker cords correctly to solve this.
What to do if “F61” appears on the display of my Panasonic Stereo System?
If “F61” appears on the display, check if the speaker cords have shorted. If the speaker cords are not shorted, this indicates a power supply problem, and you should consult your dealer for assistance.
Why does “– – : – –” appear on the display of my Panasonic SC-AK14?
The appearance of “– – : – –” on the display indicates that either you plugged the power cord in for the first time or there was a recent power failure. To fix this, set the time.
What to do if the picture on the TV disappears or stripes appear on the screen when using my Panasonic SC-AK14?
If the picture on the TV disappears or stripes appear on the screen, the location and orientation of the antenna are incorrect. If you are using an indoor antenna, change to an outdoor antenna.
What to do if the left and right sounds are reversed when listening to the external unit on my Panasonic Stereo System?
If the left and right sounds are reversed when listening to the external unit, it means the left and right connections to the external unit are reversed. Connect the external unit’s cord correctly.
What to do if I see “TAKE OUT/DISC” on the display of my Panasonic Stereo System?
If you see “TAKE OUT/DISC” on the display, it indicates there was a power failure or the power cord was disconnected from the household AC outlet during disc changing operation or when the disc tray is opened. To resolve this: 1. Press [f/7, POWER] to switch on the power. The tray will open. 2. If there is a CD in the tray, remove it, then press [c] of [CD 1] to close the tray. The system will restore normal operation.
How to fix 'rushing noise' during a stereo broadcast on my Panasonic SC-AK14 Stereo System?
If you experience a 'rushing noise' during a stereo broadcast that is not audible during a monaural broadcast, the transmitting station is likely a long distance away. If you are using an indoor antenna, switch to an outdoor antenna.
What does “ERROR” message mean on the display of my Panasonic SC-AK14 Stereo System?
If “ERROR” message appears on the display, it means an incorrect operation has been performed. Operate the unit correctly by following the operating instructions.
Why ECO mode is on but the display panel still lights up on my Panasonic SC-AK14 Stereo System?
If ECO mode is on but the display panel still lights up, it means DEMO mode is also on. Turn DEMO mode off.
Amplifier Section| RMS power output | 45 W per channel (6 Ω) |
|---|---|
| RMS power output (70 Hz–16 kHz) | 40 W per channel (6 Ω) |
| Input sensitivity (AUX) | 250 mV |
| Input impedance (AUX) | 13.9 kΩ |
FM Tuner Section| Frequency range (200 kHz steps) | 87.9 – 107.9 MHz |
|---|---|
| Frequency range (100 kHz steps) | 87.5 – 108.0 MHz |
| Sensitivity | 2.5 µV (IHF) |
| S/N 26 dB | 2.2 µV |
| Antenna terminal(s) | 75 Ω (unbalanced) |
AM Tuner Section| Frequency range (AM) | 520 – 1710 kHz (10 kHz steps) |
|---|---|
| Sensitivity (AM) | 560 µV/m |
| S/N 20 dB (at 1000 kHz) | 560 µV/m |
Cassette Deck Section| Tape speed | 4.8 cm/s |
|---|---|
| Frequency response (NORMAL TYPE I) | 35 Hz – 14 kHz |
| Frequency response (HIGH TYPE II) | 35 Hz – 14 kHz |
| S/N | 50 dB (A weighted) |
| Wow and flutter | 0.18% (WRMS) |
| Fast forward and rewind time | Approx. 120 seconds with C-60 cassette tape |
CD Section| Sampling frequency | 44.1 kHz |
|---|---|
| Decoding | 16 bit linear |
| Beam source/wave length | Semiconductor laser/780 nm |
| Frequency response | 20 Hz–20 kHz (+1, –2 dB) |
| Digital filter | 8 fs |
Speaker Section| Type | 2 way speaker system |
|---|---|
| Woofer | 12 cm (4[23]/32˝) cone type |
| Tweeter | 6 cm (2[3]/8˝) cone type |
| Impedance | 6 Ω |
| Input power | 100 W (Music) |
| Output sound pressure level | 85 dB/W (1.0 m) |
| Cross over frequency | 5 kHz |
| Frequency range | 45 Hz–22 kHz (–16 dB) |
General| Power supply | AC 120 V, 60 Hz |
|---|---|
| Power consumption | 145 W |
| Dimensions (WxHxD) | 270 x 330 x 310 mm |
| Mass | 6.8 kg (14.96 lb.) |
Covers power source, polarization, cord protection, nonuse, and installation environment.
Details unit placement, ventilation, maintenance, and service procedures.
Guides on connecting antennas, speakers, and the AC power cord.
Identifies and describes the controls and indicators on the main unit.
Explains the function of each button on the remote control transmitter.
Guides on tape types, tape-to-tape recording, and recording from radio.
Solutions for common problems with radio, CD, and cassette operations.
To Next Page