18
RQT0A22
Others
As a factory default, this unit will turn to standby mode
automatically if there is no sound and it is not being
used for approximately 20 minutes.
To cancel this function
1 Press [SETUP] repeatedly to select “AUTO OFF”.
2 Press [3, 4] to select “OFF” and then press [OK].
≥ To turn the function on, select “ON” in step 2.
≥ This setting cannot be selected when radio is the source.
≥ When connected to a Bluetooth
®
device, the function does
not work.
≥ When playing AllPlay/DLNA, the function does not work.
≥ If “NET STANDBY” is set to “ON”, this function will also be
set to “ON”. To change the setting, set “NET STANDBY” to
“OFF”. (l 19)
When “SC-ALL5CD” is selected from a paired
Bluetooth
®
device’s Bluetooth
®
menu, this unit will turn
on automatically from standby mode and establish a
Bluetooth
®
connection.
1 Press [SETUP] repeatedly to select “BLUETOOTH
STANDBY”.
2 Press [3, 4] to select “ON” and then press [OK].
≥ To turn the function off, select “OFF” in step 2.
When other Panasonic equipment responds to the
supplied remote control, change the remote control
code.
1 Press [CD/USB] to select “CD”.
2 While touching and holding [SELECTOR] on the
unit, press and hold [CD/USB] on the remote
control until the unit’s display shows “REMOTE 2”.
3 Press and hold [OK] and [CD/USB] on the remote
control for at least 4 seconds.
≥ To change the mode back to “REMOTE 1”, press [CD/USB]
to select “CD” and then repeat the step 2 and 3 but replace
[CD/USB] with [ ].
As a factory default, there will be a beep sound when
you touch the switch on the unit.
To cancel this function
1 Press [SETUP] repeatedly to select “BUZZER”.
2 Press [3, 4] to select “OFF” and then press [OK].
≥ To turn the function on, select “ON” in step 2.
≥ The function works during muting as well.
Occasionally, Panasonic may release updated
software for this system that may add or improve the
way a feature operates. These updates are available
free of charge.
Preparation
≥ Turn this system on.
≥ Connect this system to the home network. (l 7)
– Make sure that the network is connected to the
Internet.
1 Press [RADIO/EXT-IN] repeatedly to select
“NETWORK”.
2 Press [SETUP] repeatedly to select
“SW UPDATE” and then press [OK].
3 Press [3, 4] to select “OK? YES” and then press
[OK] to start the update.
≥ Select “OK? NO” to cancel the update.
When the update begins, “UPDATING” is
displayed. After the update has finished,
“SUCCESS” is displayed.
4 Disconnect the AC mains lead and reconnect it
after 1 minute.
≥ If there are no updates, “NO NEED” is displayed.
≥ Downloading will require several minutes. It may take longer
or may not work properly depending on the connection
environment.
Auto off function
Bluetooth
®
standby
Changing the unit and remote
control code
Beep sound setting
Software update
You can also update the software from a pop-up
prompting you to do so on-screen within the app
“Panasonic Music Streaming” (version 2.0.8 or later)
(l 9). For details on the app, refer to the site below.
http://panasonic.jp/support/global/cs/audio/app/
(This site is in English only.)
DO NOT DISCONNECT the AC mains lead
while one of the following messages is
displayed.
“UPDATING” or “UPD%”
(“ ” stands for a number.)
≥ During the update process, no other operations can be
performed.
SC-ALL5CD-EGEBGN~RQT0A22.book 18 ページ ２０１５年７月１７日 金曜日 午前１１時３０分
To Next Page
Loading...
