Panasonic SC-HC28 User Manual

10
RQT9736
Others
As a factory preset, this unit will always turn off
automatically if there is no sound output and no
operation for approx. 30 minutes.
To cancel this function
1 Press [SETUP] repeatedly to select “AUTO OFF”.
2 Press [3, 4] to select “OFF” and then press [OK].

≥ To turn automatic standby on, select “ON” in step 2.
The brightness of this unit’s display can be changed.
Press [DIMMER].
When other Panasonic equipment responds to the
supplied remote control, change the remote control
code.
1 Press [CD] to select “CD”.
2 Press and hold [CD] on the unit and [CD] on the
remote control until the unit’s display shows
“REMOTE 2”.
3 Press and hold [OK] and [CD] on the remote
control for at least 4 seconds.

≥ To change the mode back to “REMOTE 1”, repeat the steps
above but replace the button pressed on the remote control
from [CD] to [RADIO].
Troubleshooting
Before requesting service, make the following checks.
If you are in doubt about some of the check points, or if
the solutions indicated in the following guide do not
solve the problem, consult your dealer for instructions.
Humming heard during play.
≥ An AC mains lead or fluorescent light is near the cords. Keep
other appliances and cords away from this unit’s cables.
MP3 cannot be read.
≥ You may not be able to play MP3 if you have copied a
multi-session disc that has no data between sessions.
≥ When creating a multi-session disc, it is necessary to close the
session.
≥ The amount of data on the disc is too small. Set the amount of
data to above 5 MB.
Incorrect display or play will not start.
≥ Make sure that the disc is compatible with this unit. (l 12)
≥ There is moisture on the lens. Wait for about an hour and then try
again.
No response when [1/;] is pressed.
≥ Disconnect the USB device and then reconnect it. Alternatively,
turn the unit off and on again.
The USB drive or its contents cannot be read.
≥ The USB drive format or its contents is/are not compatible with the
unit (l 12).
≥ The USB host function of this product may not work with some
USB devices.
Slow operation of the USB flash drive.
≥ Large file size or high memory USB flash drive takes longer time
to read.
The elapsed time displayed is different from the
actual play time.
≥ Copy the data to another USB device or backup the data and
reformat the USB device.
Automatic standby
≥ This setting cannot be selected when “FM” or “AM” is the
source.
Display brightness
Changing the unit and remote
control code
To return all settings to the factory preset
When the following situations occur, reset the
memory:
≥ There is no response when buttons are pressed.
≥ You want to clear and reset the memory contents.
1 Disconnect the AC mains lead. (Wait for at least
3 minutes before proceeding to step 2.)
2 While pressing and holding down [Í/I] on the
unit, reconnect the AC mains lead.
≥ “--------” appears on the display.
3 Release [Í/I].

≥ All the settings are returned to the factory preset. You will
need to reset the memory items.
Common problems
Disc operations
USB operations
SC-HC28_GN~RQT9736-L.book 10 ページ ２０１３年２月２６日 火曜日 午後１時３９分

Panasonic SC-HC28 Specifications

General

RMS rated power	- W
Audio output channels	2.0 channels
Bluetooth	No
Headphone connectivity	-
USB 2.0 ports quantity	1
Micro-USB docking connector	Yes
Apple docking compatibility	iPad mini, iPhone 5, iPod Nano 7, iPod Touch 5
Playback disc types	CD, CD-R, CD-RW
Supported radio bands	FM
Preset stations quantity	30
Product color	Black
AC input voltage	120 V
Power source type	AC
AC input frequency	60 Hz

Weight and Dimensions

Weight	1996 g