To Next PageTo Next PageHow to clear U25/U26 error after replacing cartridge on Panasonic Air Ionizer?
If the "U25" or "U26" code persists on your Panasonic Air Ionizer after replacing the cartridge, it's likely you forgot to reset the cartridge life. Reset the cartridge life. If you reset the cartridge life with the power plug disconnected, connect the power plug, and then reset the cartridge life.
What to do if Panasonic Air Ionizer displays 'Cartridge life' when water flow is low?
If the display on your Panasonic Air Ionizer suddenly changes to "Cartridge life" when the water flow is reduced, press the water quality selector button again, turn on the faucet, and adjust the flow.
What to do if the 'Electrode cleaning' display blinks on Panasonic TK-AS66-ZEX Air Ionizer?
If the "Electrode cleaning" display is blinking on your Panasonic Air Ionizer, keep running the water for about 15 seconds.
Why is no water coming out of my Panasonic TK-AS66-ZEX Air Ionizer?
If very little or no water is coming out of your Panasonic Air Ionizer, first, ensure the faucet is fully open. Check that the water pressure isn't too low; if it is, increase the water flow at the main water supply. Also, the filter of the bypass selector may be clogged, so clean it if necessary. Other potential issues include a clogged cartridge (replace the cartridge), a cut-off water supply, or a bent/flattened water supply hose.
Why does the water from my Panasonic Air Ionizer smell bad?
If the water from your Panasonic Air Ionizer has an odor, unpleasant taste, or is turbid, it indicates that the cartridge's ability to remove these impurities has deteriorated. You should replace the cartridge.
What to do if no water from acidic spout of Panasonic TK-AS66-ZEX Air Ionizer?
If no water comes out of the acidic water spout on your Panasonic Air Ionizer when using settings other than purified water, check if the acidic water and drain hoses are bent or flattened, because if water keeps running, it may cause malfunction and prevent correct electrolysis. Also, if "Reduce flow" appears on the LCD display, reduce the water flow at the faucet slowly until the message is cleared.
Why doesn't my Panasonic TK-AS66-ZEX Air Ionizer return to 'Alkaline' setting?
If the display on your Panasonic Air Ionizer doesn't return to "Alkaline" after using the "Purified Water" setting, it may be because "OFF" has been selected for "Alkaline priority". Set "Alkaline priority" to ON. Alternatively, the "Alkaline" setting will return after about 10 minutes.
Why is my Panasonic Air Ionizer leaking from the wrong place?
If water is leaking from somewhere other than the selected spout on your Panasonic Air Ionizer, it could be due to a buildup of calcium or other minerals inside the bypass selector. To fix this, obtain some citric acid from a pharmacy, dissolve 50 g in one liter of water, and after immersing the bypass selector in the solution for about 12 hours, rinse with water.
Why doesn't the U26 code appear on my Panasonic TK-AS66-ZEX after a year?
If the "U26" code doesn't appear on your Panasonic Air Ionizer even after a year, it may be because the ionizer hasn't been used enough to reach the cartridge replacement guideline (12,000 liters). Check the cartridge life display. It is also recommended to replace it after using it for a year.
What to do if the 'Preparation time' display blinks on Panasonic TK-AS66-ZEX Air Ionizer?
If the “Preparation time” display blinks on your Panasonic Air Ionizer, keep running the water for 3 or 4 minutes.
General| Brand | Panasonic |
|---|---|
| Model | TK-AS66-ZEX |
| Category | Air Ionizer |
| Language | English |
Instructions regarding the power cord and plug to prevent hazards.
Warning against disassembly and guidelines for using approved tap water.
Precautions for users with health issues and for supervising children.
Precautions for maintenance and keeping items away from children.
Water types not for consumption and guidelines for storing water.
Actions for adverse health effects and safety with pH test liquid.
Types of water to avoid and general usage rules.
Steps for connecting the water supply hose to the bypass selector.
Connecting the power plug and initial power-on indicators.
Steps for operating the unit to produce different types of water.
Troubleshooting guide based on LCD display messages.
Further troubleshooting based on LCD display messages.
Diagnosing issues related to water flow and output.
Diagnosing issues like low water output, warm water, or buzzer problems.
Addressing issues like strange sounds, height differences, and pH level discrepancies.
