To Next PageTo Next PageWhat to do if LCD panel is dark on Panduit Printer?
If the LCD panel on your Panduit Printer is dark but the LEDs are “ON”, turn the printer “OFF” and “ON” again. If the issue persists, initialize the printer.
Why does my Panduit TDP43HE Printer skip labels when printing?
If your Panduit Printer is skipping labels, check if the label size is set up correctly. Calibrate the sensor using Auto Gap or Manual Gap options. Clear any dust from the GAP/Black mark sensor using a blower.
Why is printing missing on the sides of labels from my Panduit TDP43HE?
If printing is missing on the left or right side of the label when using your Panduit Printer, set the correct label size.
What to do if my Panduit TDP43HE says 'Carriage Open'?
If your Panduit Printer displays 'Carriage Open', close the print carriage.
How to fix unstable label feeding on Panduit TDP43HE Printer?
If the label feeding is not stable (skew) when printing with your Panduit Printer, the media guide may not be touching the edge of the media. If the label is moving to the right, move the label guide to the left. If the label is moving to the left, move the label guide to the right.
What to do if my Panduit TDP43HE shows 'Memory full'?
If your Panduit Printer displays a 'Memory Full' error (FLASH / DRAM), delete unused files in the FLASH/DRAM. Note that the maximum number of files for DRAM is 256, with a user addressable memory space of 2048KB, and for FLASH, the maximum is 256 files with a user addressable memory space of 6656 KB.
Why doesn't the power indicator illuminate on my Panduit TDP43HE?
If the power indicator on your Panduit Printer does not illuminate, the power cord may not be properly connected. Plug the power cord into both the printer and the outlet, then switch the printer on.
How to correct the vertical printing position on Panduit TDP43HE?
If the vertical printing position is incorrect on your Panduit Printer, ensure the correct label size is set. Adjust the Top Offset (Print Features) or Label Offset (Print Properties Advanced Setup) parameters within the “Print” windows.
How to correct the horizontal printing position on Panduit TDP43HE Printer?
If the horizontal printing position is incorrect on your Panduit Printer, ensure the label size is set correctly. Fine-tune the Shift X parameter by pressing [MENU] [SELECT] x 3 [DOWN] x 5 [SELECT]. Adjust “Left Offset” in Print Features.
What to do if my Panduit TDP43HE Printer says 'No Ribbon'?
If your Panduit Printer shows a 'No Ribbon' error, it may be due to running out of ribbon or incorrect ribbon installation. Replace the ribbon roll. Refer to the user’s manual for instructions on how to reinstall the ribbon correctly.
General| Printer Type | Thermal Transfer Printer |
|---|---|
| Print Technology | Thermal Transfer |
| Print Resolution | 300 dpi |
| Operating System Compatibility | Windows |
| Power Requirements | 100-240 VAC, 50/60 Hz |
| Print Speed | 4 in/sec |
| Connectivity | USB, Serial, Ethernet |
| Application | Labeling |
| Supported Media Types | Continuous, Die-cut |
| Media Thickness | 0.0025 in to 0.01 in |
| Ribbon Type | Wax, Resin, Wax/Resin |
| Ribbon Length | 984 ft (300 m) |
| Operating Temperature | 41°F to 104°F |
| Humidity | 10% to 90% non-condensing |
Provides step-by-step instructions for connecting and preparing the printer for use.
Detailed instructions for installing a new ribbon roll and removing used ones.
Guides on loading internal and external media rolls, including sensor calibration.
Covers sensor status checks and calibration procedures for Gap, Bline, and Continuous media.
Setup and management of network connectivity, including IP address, DHCP, and static settings.
Guide for configuring the printer's Ethernet settings using a USB connection to the PC.
Guide for configuring the printer's Ethernet settings using an RS-232 serial connection.
Instructions for configuring Ethernet settings directly over the network interface.
Lists frequent operational problems and their corresponding recovery procedures.
