Parker DC590+ - User Manual

To Next Page

P OWER CONNECTIONS

B EFORE YOU START

This document covers the steps necessary

for a basic start up of the DC590+DRV drive.

Drive start ups should be performed b

qualified electrical technicians who are

familiar with DC drives and their applica-

tions. For detailed safety, installation, ad-

vanced features and applications on the

590+, refer to the Product Manual.

Ensure that all local electric codes are met

while installing the drive. Check that all live

parts are covered to protect against electric

shock and that unexpected rotation of the

motor will not result in bodily harm or injury.

This document expects that the drive is

already installed in its intended location and

that all relevant installation procedures

have been followed. Please ensure that the

drive has adequate ventilation so that ambi-

ent temperature does not exceed 45°C

(112°F) under normal operating conditions.

To access the bottom layer, slide off the

bottom terminal cover and unfasten the two

retaining screws. Hinge the plastic body

upwards and engage the support bar.

• 3-phase supply to L1, L2, L3

• Motor armature to A+, A-

• Motor fields to F+, F-

• Motor thermistor to Th1, Th2

• Control supply to L, N. Check

drive nameplate for correct aux

voltage supply rating

• Blower to BL1, BL2, BL3, if fitted

thermistor

control power

field

armature

3 phase powe

3 phase power

Frame 2 (165A)

C ONFIGURE I/O

Under MENU LEVEL\SYSTEM\CONFIGURE I/O, you

may connect and disconnect internal block diagram con-

nections, to use special functions like PID, winder blocks,

diameter block, etc., and to tag analog and digital I/O to

selected points inside the drive to suit your application

needs.

S ERIAL LINKS

Under MENU LEVEL\SERIAL LINKS, you may access

parameters related to Techboxes, the system port (P3),

and all the PNO configuration parameters.

S ETUP PARAMETERS

Under MENU LEVEL\SETUP PARAMETERS, there are

several submenus where you can enter setup parame-

ters. They are:

Ramps, Auxiliary I/O, Op Station, Jog/Slack, Raise-

Lower, Preset Speeds, Special Blocks, Field Control,

Current Profile, Inverse Time, Stop Rates, Calibration,

Inhibit Alarms, Current Loop, Speed Loop, Standstill,

Setpoint sum 1.

Under MENU LEVEL\PASSWORD, you may enter a

password to protect against unauthorized access to the

drive setup parameters. Refer to the 590+ product manual

for details.

A LARMS & PASSWORD

Under MENU LEVEL\ALARM STATUS, you may view

the active and last alarm status.

A RMATURE AUTOTUNE

• In the configure drive menu, set Autotune to ARM

•

On the keypad, press L/R for LOCAL mode

•

Ensure that the motor shaft is not allowed to rotate

•

Press RUN. Drive will begin autotuning the armature.

•

When the drive stops and no error message is dis-

played on the MMI,

the autotune was successful.

• Go to MENU LEVEL\SAVE PARAMETERS and save

your settings.

F IELD AUTOTUNE

• In the configure drive menu, set Autotune to FLD

•

On the keypad, press L/R for LOCAL mode

•

Press RUN. Drive will begin autotuning the field.

•

When the drive stops and no error message is dis-

played on the MMI,

the autotune was successful.

Parker Hannifin Corporation

SSD Drives Division

9225 Forsyth Park Drive

Charlotte, NC 28273 USA

www.SSDdrives.com

Main (704) 588-3246 Support (704) 602-6062

HA470388U200 Issue 6

DC590+ DRV

Series 2

Quick Start

Frame 2

165 amps

Need help?

Do you have a question about the Parker DC590+ and is the answer not in the manual?

Summary

Field Autotune and Setup

Field Autotune Process

Procedure to autotune the drive's field. Set Autotune to FLD and press RUN.

Armature Autotune Process

Procedure to autotune the drive's armature. Set Autotune to ARM and press RUN.

Setup Parameters Overview

Accessing submenus for Ramps, Auxiliary I/O, Op Station, Jog/Slack, etc.

Alarms and Password Protection

Viewing alarm status and setting passwords for drive access protection.

Configure I;O Functionality

Connecting internal block diagram connections for PID, winder blocks, etc.

Serial Links Configuration

Accessing parameters for Techboxes, system port (P3), and PNO configurations.

Before You Start and Power Connections

Startup and Installation Precautions

Covers basic startup steps and general installation safety precautions.

Power Connection Details

Connecting 3-phase supply, armature, field, thermistor, and blower terminals.

Reference and Sequencing Inputs

Speed Reference Input

Connecting speed potentiometer or external 2-wire speed reference.

Sequencing Input Connections

Wiring for E-Stop relay, trip contact, enable, start, jog, and health relay.

Speed Feedback Configuration

Speed Feedback Modes

Default mode (Armature Voltage) and available feedback cards.

Feedback Card Installation

Selecting, installing, and setting up feedback cards (Analog Tach, Encoder, Microtach).

Drive Calibration Procedure

Calibration Steps

Software calibration process via keypad, entering motor parameters.

Parameter Settings for Calibration

Setting motor volts, armature/field current, limits, encoder details, and speed loop gains.

Saving Calibration Settings

Disabling configuration mode and saving parameters after calibration.