Paslode Cordless Framing Nailer

Questions and Answers

A
Alexandra BrownSep 8, 2025
What to do if my Paslode Nail Gun won't cycle but the fan runs and the light is green?
- A
  Anthony WolfSep 8, 2025
  If your Paslode Nail Gun's fan runs and the indicator light is solid green but the tool won't cycle, the fuel cell may be empty, so replace it. Also, the spark wire might be out of the spark plug; remove the cap, check the spark lead, insert it into the spark plug, and replace the cover. The spark plug could also be dirty, so clean the tool cylinder head and spark plug. If no spark is generated, return the tool to an authorized Paslode dealer for service.
D
david81Sep 7, 2025
Why Paslode Cordless Framing Nailer driver blade did not return to up position?
- D
  David ParkerSep 7, 2025
  If the Paslode Nail Gun operated and drove fasteners, but the driver blade did not return to the up position: * There could be built-up dirt and debris on the driver blade or in the nose bore. Clean the driver blade and nose bore with degreaser cleaner. * The mid check might be dirty or disabled. Return the tool to an authorized Paslode® Cordless dealer for service.
A
Alexandra RogersAug 22, 2025
Why won't my Paslode Nail Gun drive nails all the way?
- S
  Stacey WilliamsAug 22, 2025
  There are several reasons why your Paslode Nail Gun might not be driving fasteners fully. The work-contacting element may require adjustment, so try adjusting it. The fuel cell could be low, so check it and replace it if needed. There might also be a loss of seal in the combustion chamber. To check for a leak, press the work-contacting element against the workpiece for one minute and pull the trigger; if the fastener doesn't drive, a leak requiring service is present.
K
kimberlyfrazierSep 4, 2025
What to do if Paslode Nail Gun fan does not run and the indicator light is red?
- M
  Madison HensonSep 4, 2025
  If the fan on your Paslode Nail Gun doesn't run and the tool indicator light is blinking or solid red: * The battery might not be charged; charge the battery. * The battery terminals could be oily, dirty, or corroded; clean them with fine emery cloth.
T
Timothy GonzalezSep 3, 2025
What to do if Paslode Cordless Framing Nailer operates erratically and loses power?
- C
  Christine MillerSep 3, 2025
  If your Paslode Nail Gun operates erratically or seems to lose power while the indicator light is green, check the following: * The fuel cell might be low, so check it. * The spark plug wire could be loose, so inspect it. * The filter element might be dirty, causing the tool to overheat. Remove the filter element and clean it, using soap and water for stubborn debris.
K
kelsey11Sep 1, 2025
Why didn't the driver blade return to the up position on my Paslode Cordless Framing Nailer?
- R
  Ryan BakerSep 1, 2025
  If the tool operated and drove fasteners, but the driver blade didn't return to the up position, there could be built-up dirt and debris on the driver blade or in the nose bore, so clean the driver blade and nose bore with degreaser cleaner. Alternatively, the mid check might be dirty or disabled, so return the tool to an authorized Paslode® Impulse dealer for service.
K
Karen AlexanderAug 31, 2025
Why is my Paslode Cordless Framing Nailer fan running slow and the indicator light is solid red?
- F
  frodriguezAug 31, 2025
  If the fan doesn't run or runs slower than normal and the tool indicator light is solid red, the battery is likely discharged, so charge the battery.
J
Jerry SingletonAug 30, 2025
What to do if the work-contacting element on my Paslode Nail Gun won't depress fully?
- A
  Amber RiveraAug 30, 2025
  If the work-contacting element does not depress fully and the tool doesn't operate, the lockout bracket might be stuck in the lockout position, so check the lockout. If you can't free it, return the tool to an authorized Paslode dealer for service. The work-contacting element could also be bent, or debris buildup in the track might restrict operation; remove and inspect the lower probe, then clean and lubricate the track with Paslode Impulse® oil. Repair or replace the lower probe as needed. Also, ensure the follower is positioned behind the fasteners.
L
leonardhodgesAug 29, 2025
Why does my Paslode Nail Gun operate but not drive fasteners?
- R
  rcruzAug 29, 2025
  If your Paslode Nail Gun operates but doesn't drive fasteners, you might be using the wrong fasteners, so use only fasteners meeting Paslode specifications. The follower might not be properly engaged behind the fastener strip, so position it behind the strip and engage it. There could also be a jammed fastener, so clear the jam.
W
wpeckAug 27, 2025
Why is the indicator light blinking red on my Paslode Cordless Framing Nailer and the fan not running?
- R
  Rebecca MillerAug 27, 2025
  If the fan doesn't run and the tool indicator light is blinking red or solid red, the battery may not be charged, so charge it. Alternatively, the battery terminals could be oily, dirty, or corroded; clean them with fine emery cloth.

Summary

Introduction and Warranty

Paslode Cordless Warranty and Limitations

Details Paslode's limited warranties for tools, parts, and accessories.

An Overview of the Paslode Cordless Framer

Description

Provides a general description of the Paslode Cordless framer's functionality.

Specifications

Lists key technical specifications like weight, dimensions, and cycle rate.

Safety Instructions

General Warnings and Hazards

Covers combustion, ventilation, temperature, child safety, and initial precautions.

Safe Operation Practices

Includes eye/ear protection, tool handling, trigger use, fastener loading, and discharge prevention.

Work-Contacting Element and Driving Safety

Addresses safe use of the work contacting element and proper fastener driving locations.

Environmental and Storage Safety

Covers hazardous areas, high locations, qualified personnel, storage, and battery disposal.

Battery and Charging System

Charging Instructions and Notes

Details charging procedures, times, important notes, and warnings for the battery.

Charging System Accessories

Lists optional accessories available for the Paslode cordless charging system.

Inserting and Removing Battery

Provides steps for inserting and removing the battery, and cleaning terminals.

Battery Indicator Light Operation

Explains the function and color codes of the battery indicator light on the tool.

Fuel Cell and Metering Valve

Fuel Cell and Metering Valve Overview

Explains fuel cell structure, operation, hazards, metering valve function, and handling.

Attaching Valve and Fuel Cell Insertion

Guides on attaching the metering valve, inserting the fuel cell, and closing the cover.

Fuel Cell Maintenance and Safety

Covers fuel cell replacement, expiration dates, storage, and flammability dangers.

Preparing the Paslode Cordless Framer for Use

Fastener Loading

Illustrates the correct procedure for loading fasteners into the nailer magazine.

Outdoor Weather Operation

Provides guidelines for operating the tool in various outdoor weather conditions.

Hot Weather Operation

Advises on managing tool performance and preventing overheating in hot conditions.

Cold Weather Operation

Offers recommendations for operating the tool effectively in cold temperatures.

Paslode Cordless Framer Operation

Press Work Contacting Element

Explains the initial step of pressing the work contacting element against the surface.

Trigger Operation

Details the function of squeezing the trigger to ignite the combustion chamber.

Depth of Drive Adjustment

Guides on adjusting the work-contacting element to control fastener depth.

No-Mar Work-Contacting Element

Introduces an optional accessory for mark-free applications.

Fasteners and Applications

Application Diagram

Illustrates various construction applications for the Paslode nailer.

Fastener Size and Type Chart

Lists fastener sizes, types, and their corresponding construction applications.

Fastener Descriptions

Explains different fastener types like smooth shank, ring shank, and galvanized.

Impulse Cordless Framer Nail Compatibility

Details specific nails driven by the Impulse Cordless Framer, including part numbers.

Servicing

Restrict Field Service

Lists procedures that can be performed by the user vs. requiring a technician.

Fuel Cell Check

Procedure to check fuel cell status and determine if it needs replacement.

Battery Check

Guidance on checking battery charge level and indicator light status.

Clearing a Jam

Step-by-step instructions for safely clearing jammed fasteners from the tool.

Air Filter Maintenance

Instructions for cleaning and maintaining the tool's air filter for optimal performance.

End-of-Workday Routine

Recommended steps to perform at the end of each workday for tool care.

Troubleshooting

Battery;Charger Problems

Addresses issues related to the battery not charging or the charger overheating.

Normal Stage of Operation Issues

Diagnoses problems like the fan not running or slow operation based on indicator lights.

Pre-Combustion;Combustion Stage Issues

Troubleshoots issues preventing the tool from operating or cycling.

Power;Exhaust Stage Operation Issues

Solves problems with fasteners not driving fully, over-driving, or not driving at all.

Returning;Purging Stage Issues

Addresses issues where the driver blade does not return or the combustion chamber does not drop.