CARE AND MAINTENANCE
TROUBLESHOOTING
Before cleaning:
1. Ensure the power is off.
2. Use a damp cloth to clean the fixture.
3. Do not use detergent or abrasives for cleaning.
SKU Number: 356-1279
Model Number: OWL2223
1-Light Outdoor Wall Light
PACKAGE CONTENTS
HARDWARE CONTENTS Note: Hardware not shown actual size.
Lock nut x 4
(2pcs pre-attached, 2pcs spare)
Mounting bracket with
ground screw (pre-attached)
x 1
AA
Wire connector
x 3
Outlet box screw
x 2
BB
CC
DD
R
R
R
R
FIVE-YEAR LIMITED WARRANTY: If, during normal use, this PATRIOT LIGHTING lighting fixture breaks or fails due to a defect in material
workmanship within five (5) years from the date of original purchase, simply bring this lighting fixture with the original sales receipt back to
your nearest MENARDS retail store. At its discretion, PARTIOT LIGHTING agrees to have the product or any defective part(s) repaired or
replaced with the same or similar PATRIOT LIGHTING product or part free of charge, within the stated warranty period, when returned by
the original purchaser with original sales receipt. This warranty; (1) excludes expendable parts including but not limited to light bulbs; (2) does
not cover damage that has resulted from abuse or misuse; and (3) does not cover any losses, labor, injuries to persons/property or costs.
This warranty does give you specific legal rights and you may have other rights, which vary from state to state.
Rubber washer x 4
(2pcs pre-attached, 2pcs spare)
EE
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
WARNING
Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or
switching off circuit breaker).
Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to
contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause
serious injury or death from electric shock.
This product must be installed in accordance with the applicable installation code by a person familier with the
construction and operation of the product and hazards involved.
Adjustment of the TIME and LUX:
Twist the finial (C) off, take off the washer and cap (D) from the unit. You could adjust the TIME and LUX by turning
the knob.
LUX: From 1 to 1000
TIME: From 5 seconds to 2 minutes
+
-
FUNCTION AND OPERATION (continued)
Issues
1. Turn light switch on.
2. Check bulb and replace if burned out.
3. Replace fuse or turn circuit breaker on.
4. Recheck after dark.
5. Re-aim the sensor to cover desired area.
6. Verify wiring is correct.
1. Light switch is turned off.
2. Light bulb is loose or burned out.
3. Fuse is blown or circuit breaker is turned off.
4. Daylight turn-off is in effect.
5. Sensor is not detecting movement.
6. Incorrect circuit wiring, if a new installation.
Lights will not
come on
Lights stay on
continuously
The sensor may be picking up a heat source
like an air vent, dryer vent, etc.
Reinstall the unit away from heat source.
Possible cause Solution
C
D
The TIME setting controls how long the unit remains illuminated following activation &
after all motion ceases. The minimum time is 5 seconds, while the maximum time is
2 minutes. Set the control to the desired setting between these limits.
14
The LUX control determines the level of darkness required for the unit to start operating.
Set the LUX control knob fully counterclockwise, the unit will now start operating at dusk.
If you require the light to activate earlier, wait until the ambient light level reaches the
level of darkness at which you wish the lamp to become operative, slowly rotate the
control clockwise until a point is reached where the lamp illuminates, leave the control
set at this point.
+
-
Questions, problems, missing parts?
Please email us at customer-service@ewccglobal.com.cn,
or call us at 1-888-722-5089.
To Next Page
Need help?
General
