Patriot Lighting 356-9231 - User Manual

Page 1 / 6
Important to Know:
1. If you are not familiar with state and local electrical
codes, it is recommended that you consult with a
qualified electrician.
2. This fixture requires a 120 VAC, 60 Hz power
source.
3. For general safety and to avoid any possible
damage to the sensor, be sure the power is
switched "off" before adjustment.
Maximum Wattage: 2-150 W (bulb included)
Working Temperature Range: - 4
0
F ~ 113
0
F
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Customer Service: 1-800-887-6326 (weekdays 9 a.m. – 5 p.m. CST)
3. READ AND SAVE THESE INSTRUCTIONS.
356-9231 / 356-9232
150619
Features:
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Note: Fixture can be wall mounted or eave mounted.
Wall Mounted
Eave Mounted
Read notes section on page 4 for additional information about mounting location of fixture.
Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)
Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for
proper operation and to avoid the risk of electrical shock.
For eave mounted only:
Rotate the sensor head towards the back plate.
Rotate the sensor head clockwise 180˚ so the controls face down.
Controls
Back Plate
Controls
Controls
1. Motion sensor: turns light ON automatically when
motion is detected and turns light OFF automatically
when motion stops.
2. Photocell keeps the light OFF during daylight hours.
Hardware Package (included):
Decorative cover
Fixture Mounting Screw
Mounting Strap
Wire Nut X3
Gasket
Mounting Screw X2
#8/32X1/2 in
Mounting Screw X2
#6/32 X1/2 in
Mounting Screw X2
#10/24 X1/4 in

Summary

Assembly and Installation Instructions

Electrical Shock Warning

Ensure power is shut off before installation or servicing to prevent electrical shock.

Important Installation Information

Consult local codes, use a qualified electrician if unfamiliar, and verify power source.

Product Features

Details motion sensor activation and photocell daylight operation.

Mounting Options

Fixture can be mounted on a wall or eave.

Installation Steps

Power Off and Mounting Strap Installation

Turn off power, install mounting strap securely to the outlet box.

Wire Connections and Fixture Attachment

Connect fixture wires using wire nuts and attach the back plate to the mounting strap.

Sealing and Final Assembly

Caulk around the back plate to prevent water seepage and push decorative cover.

Replacing Light Bulbs

Instructions for safely replacing the halogen bulb without touching it.

Sensor and Light Head Adjustments

Adjusting the Sensor Head Position

Aim sensor head for desired detection area, keeping controls facing down.

Motion Sensor Sensitivity Settings

Adjust sensitivity for desired performance and detection range.

Adjusting the Light Head Position

Tilt light heads for coverage, keeping them below horizontal.

Function and Operation Modes

Operational Modes Explained

Details TEST, OFF, 3 HOUR, 6 HOUR, and D2D modes for nighttime operation.

Customization: Shut-off Delay

Adjust the time the light stays on after motion stops using the Time knob.

Performance Notes and Troubleshooting

Sensor Sensitivity and Maintenance

Sensitivity varies with temperature; clean lens regularly for optimal performance.

Optimal Installation Height and Range

Install at least 8 feet high for up to 70 feet detection distance.

Troubleshooting Common Issues

Addresses lights not coming on, false triggering, and flashing.

Warranty Information

5-Year Limited Warranty Coverage

Covers defects in material/workmanship; excludes bulbs, glass, and misuse.

Contact Information for Support

Provides customer service number for questions or reordering parts.

Patriot Lighting 356-9231 Specifications

General

Brand	Patriot Lighting
Model	356-9231
Category	Outdoor Light
Language	English