Pedigo P-2010 - Page 5

Pedigo P-2010, P-2020, P-2030, P-2040, P-2050, P-2055 Blanket Warming Cabinets Operation and Care Manual
4
GENERAL INFORMATION
This warming cabinet is designed to elevate blanket
temperatures to a level which will increase patient
comfort.
The warming cabinet is constructed with 20 gauge
stainless steel exterior casing and door with handle and
hinges designed to withstand heavy usage. A door with
window allows observation of inventory with the door
closed. The cabinet is warmed using the patented Halo
Heat® low-heat-density electrothermal cable array. The
electrothermal cable is positioned in the floor and two
sides of the warming cabinet, providing even heating of
the interior chamber. The interior chamber temperature is
regulated by an electronic control. The design and
operational characteristics of the cabinet eliminate the
need for a heat circulating fan.
The electronic control consists of a 4 digit L.E.D. display,
ON/OFF key, INCREASE and DECREASE keys, integrated
LOCK feature and a series of prompt sequence indicators.
The electronic control has an adjustable temperature
range of 37° to 94°C (98° to 200°F). A warming shut-off
system, separate from the electronic control, prevents
overheating.
The TIMER key allows the user to program the control to
automatically turn on and turn off once during a 24 hour
period at selected times. The electronic control can easily
be set to operate in Fahrenheit or Celsius. After a power
failure, the cabinet will remember its programming and
begin to operate as before. The ON/OFF indicator will
blink to indicate a failure occurred; pressing the ON/OFF
key once will eliminate this blinking.
P-2010 INFORMATION
The P-2010 warming cabinet is equipped with one (1)
white, epoxy-coated blanket support assembly. The
cabinet is furnished with four (4) 1-1/4" (31mm) non-skid
rubber feet.
P-2020 INFORMATION
The P-2020 warming cabinet is equipped with one (1)
white, epoxy-coated blanket support assembly and one
(1) center shelf. The cabinet is furnished with one (1) set
of 5" (127mm) heavy duty casters, two with locking brake.
P-2030 INFORMATION
The P-2030 warming cabinet is equipped with one (1)
white, epoxy-coated blanket support assembly and one
(1) center shelf. The cabinet is furnished with one (1)
set of 5" (127mm) heavy duty casters, two with locking
brake.
P-2040 INFORMATION
Each P-2040 chamber is equipped with one (1) white, epoxy-
coated blanket support assembly and one (1) center shelf.
The cabinet is furnished with one (1) set of 5" (127mm)
heavy duty casters, two with locking brake.
P-2055 INFORMATION
Each P-2055 chamber is equipped with a white epoxy-
coated blanket support assembly and two (2) center
shelves. The cabinet is furnished with one (1) set of 5"
(127mm) heavy duty casters, two with locking brake.
P-2050 INFORMATION
Each P-2050 chamber is equipped with a white epoxy-
coated blanket support assembly. The cabinet is furnished
with one (1) transport handle on each end of the cabinet,
and a full-perimeter rubber bumper assembly with 5"
(127mm) heavy duty casters, two with locking brake.
DANGER
AT NO TIME SHOULD THE INTERIOR
OR EXTERIOR BE STEAM CLEANED,
HOSED DOWN, OR FLOODED WITH
WATER OR LIQUID SOLUTION OF
ANY KIND. DO NOT USE WATER JET
TO CLEAN.
SEVERE DAMAGE OR
ELECTRICAL HAZARD
COULD RESULT.
WARRANTY BECOMES VOID IF
APPLIANCE IS FLOODED
DANGER
DO NOT use this warming cabinet in
the presence of flammable
anesthetic mixture (with air or with
oxygen or nitrous oxide).
THIS COULD RISK AN EXPLOSION!