Need help?Do you have a question about the Pentair FP0S1300X and is the answer not in the manual?
Crucial instructions for installation, operation, and maintenance of the pump.
Warning regarding chemicals known to cause cancer or reproductive harm.
Covers safe practices for pump installation, operation, and maintenance.
Overview of the Pentair Flotec Submersible Utility Pump and its intended use.
Step-by-step guide for correctly installing the submersible utility pump.
Instructions for safe and effective operation of the submersible utility pump.
Explains airlocks and how to resolve them using the anti-airlock hole.
Details technical specifications for the pump, including power and dimensions.
Provides solutions for common pump problems like not starting or low water flow.
Outlines the terms and conditions of the limited warranty for Pentair Flotec products.
Details specific warranty durations for different Pentair Flotec product lines.
Covers general warranty conditions, exclusions, and limitations of remedies.
The Pentair Flotec Submersible Utility Pump, available in models FPOS1300X and FPOS1600X, is a versatile and robust device designed for efficient water removal from various locations. This pump is ideal for draining water from basement floors, stock tanks, window wells, boats, flat roofs, and cisterns, making it a valuable tool for both residential and light commercial applications. Its submersible design allows it to be placed directly into the water source, ensuring effective and continuous operation.
One of the primary functions of this pump is its ability to handle significant volumes of water. It is equipped with a powerful motor that ensures quick and thorough drainage. The pump is designed to operate in water depths as shallow as 1/2 inch (12.7 mm) for starting, and can reduce the water level down to 3/16 inch (4.75 mm) before losing suction. This low-level drainage capability is particularly useful for situations where minimal residual water is desired, although a mop or squeegee will be needed to remove any remaining water below the 3/16 inch threshold.
The pump is engineered for user convenience and safety. It features a 3-prong grounding-type power cord, which must be connected to a properly grounded, grounding-type receptacle to prevent electrical shock. For optimal safety, it is crucial to ensure that the power source conforms to the pump's requirements of 115V, 60 Hz, and an individual branch circuit of 15 Amp or more capacity. The motor shaft bearings are permanently lubricated, eliminating the need for routine lubrication maintenance.
A key safety feature of the Pentair Flotec Submersible Utility Pump is its automatic resetting thermal overload protector. This protector is designed to safeguard the motor from overheating, which can occur due to various factors such as low heads (low discharge restriction), excessively high or low voltage, inadequate wiring, incorrect motor connections, or a defective motor or pump. If the motor becomes too hot, the overload protector will automatically shut off the pump to prevent damage and will reset itself once the motor has cooled sufficiently, allowing the pump to restart. However, if the overload protector trips repeatedly, it is essential to disconnect the power and investigate the underlying problem.
Installation of the pump is straightforward. It should be placed on a level, solid foundation, and never suspended by its discharge pipe or power cord. The pump inlet screen must be kept clear of debris to ensure optimal performance. For discharge, users can either install a garden hose using the provided adapter or a rigid plastic pipe. When using a garden hose, it is recommended to use a 3/4-inch diameter hose and the shortest possible length to maintain the optimal flow rate. If a rigid pipe is preferred, plastic pipe with pipe thread sealant tape should be screwed into the pump body hand tight, plus an additional 1 to 1-1/2 turns.
The pump is designed for continuous operation in water depths above 3/16 inch, as the pumped water helps cool the motor. If the motor overload trips, it is advised to allow the pump to cool for one hour before restarting. It is crucial not to leave the pump unattended during operation. If the discharge stream suddenly stops, the pump should be immediately stopped to prevent it from running dry, which can damage the shaft seal.
To prevent airlocks, which can cause the pump to run without moving water and lead to overheating and failure, the pump is equipped with an anti-airlock hole at the bottom of the pump body. If an airlock is suspected, the pump should be unplugged, the anti-airlock hole cleaned with a paper clip or wire, and then restarted. It is important to note that leakage from this anti-airlock hole is normal and necessary for the pump to prime within 15 seconds in as little as 1/2 inch of water.
Maintenance of the Pentair Flotec Submersible Utility Pump primarily involves periodic inspection and cleaning. Users should regularly check the pump and system components, ensuring the sump, pump, and system are free of debris and foreign objects. Hoses should be checked for weak or worn conditions before each use, and all connections must be secure. Disconnecting power before servicing any component is a critical safety measure. Releasing all pressure and draining all water from the system before servicing are also essential steps.
The pump is specifically designed for pumping water and should not be used with salt water, brine, or for applications involving waterfalls or fountains, as this will void the warranty. It is also not intended for use as a swimming pool drainer or in water where fish are present, as any oil leaks from the motor could harm or kill aquatic life. The product is not designed for applications where water recirculates.
In summary, the Pentair Flotec Submersible Utility Pump is a reliable, user-friendly, and safety-conscious device for various water drainage needs. Its robust construction, automatic thermal protection, and straightforward installation and maintenance procedures make it an efficient solution for managing unwanted water in diverse environments.
General| Model | FP0S1300X |
|---|---|
| Category | Water Pump |
| Type | Submersible |
| Max Flow Rate | 1300 GPH |
| Voltage | 115V |
| Discharge Size | 1.5 in |
| Weight | 9.5 lb |
| Port Size | 1.5 in |
| Horsepower | 1/4 HP |
To Next Page