To Next Page
N
natalielopezSep 23, 2025
What to do if sweep hose is caught in Pentair Swimming Pool Vacuum tube?
- JJames Pearson MDSep 23, 2025
Ensure the sweep hose regulator valve is fully open.
What to do if sweep hose is caught in Pentair Swimming Pool Vacuum tube?
Ensure the sweep hose regulator valve is fully open.
What to do if Pentair Swimming Pool Vacuum will not climb?
If your Pentair Swimming Pool Vacuum cleaner will not climb, check the debris bag and empty it if it's full. Ensure proper water flow using the Flow Gauge and adjust the flow at the wall fitting if needed. Reposition the thrust jet to improve climbing. Keep in mind that the climbing ability depends on the pool shape and available water flow; it will perform better in pools without sharp angles or in the transition from the pool floor to the pool wall.
What to do if Pentair Swimming Pool Vacuum hangs at steps?
If your Pentair Swimming Pool Vacuum cleaner hangs at steps, ensure the front (large) wheels reverse approximately every 2-1/2 minutes.
Why Pentair RACER brush on front of cleaner is not spinning?
If the brush on the front of your Pentair Swimming Pool Vacuum isn't spinning, watch the front wheels while the cleaner is operating in the pool. The wheels and front brush should rotate simultaneously. Ensure the scrubber is free of tangled debris.
Why Pentair RACER Swimming Pool Vacuum rear wheels dragging or not spinning?
If the rear wheels of your Pentair Swimming Pool Vacuum are dragging or not spinning, make sure the wheel sleeve is free of tangled debris. You may need to remove the wheel to remove any tangled debris.
Why are the hoses tangling in loops on my Pentair Swimming Pool Vacuum?
To resolve tangling hoses in your Pentair Swimming Pool Vacuum, check the length of the feed hose, as it may be too long. Ensure the feed hose floats on the pool surface with floats spaced about two feet apart. Also, verify that the hose swivels spin freely and replace them if they are tight. Make sure the feed hose has no kinks or bends.
Why Pentair RACER booster pump very noisy?
If your Pentair Swimming Pool Vacuum is making a lot of noise, make sure the filter pump and booster pump are on and moving water; you might need to clean your pool filter system. Check that the wall fitting is properly installed, and if it's leaking, the O-ring may need to be replaced. It is also possible booster pump issue, so contact your local pool professional.
What to do if Pentair RACER tilts to one side?
If your Pentair Swimming Pool Vacuum cleaner tilts to one side, empty the debris bag. The cleaner may sometimes tilt on one side during a turn cycle; observe it for a few minutes to see if it returns to an upright position.
Why is my Pentair Swimming Pool Vacuum booster pump very noisy?
If your Pentair Swimming Pool Vacuum's booster pump is very noisy, ensure that both the filter pump and booster pump are on and moving water. Cleaning your pool filter system may be necessary. Also, ensure the wall fitting is properly installed. If it's leaking, the O-ring may need replacement. It could also be a booster pump issue, so contact your local pool professional.
Why is the brush on the front of my Pentair Swimming Pool Vacuum not spinning?
If the brush on the front of your Pentair Swimming Pool Vacuum isn't spinning, watch the front wheels while the cleaner is running in the pool. The wheels and front brush should rotate at the same time. Make sure the scrubber is free of any tangled debris.
Guidance on preparing for cleaner installation, including pool surface checks.
A list of essential checks and preparations before installing the pool cleaner.
Step-by-step guide for attaching the wall fitting and adapter.
Procedure for adjusting water flow using the flow gauge and wall fitting.
Steps for attaching the hose and debris bag to the cleaner head.
General| Type | Robotic |
|---|---|
| Pool Type | In-ground |
| Remote Control | No |
| Warranty | 2 years |
| Compatibility | All pool surfaces |
| Cable Length | 60 feet |
| Features | energy efficient |
| Cleaning Cycle | 2.5 hours |
