Pentair SunTouch Quick Reference Guide

Shared Equipment/Single Body
1. Press Menu button until Advanced 8/14 displays.
2. Press Right button to access Advanced menu.
3. Press Right button to System Type.
4. Press Up/Down button to select Single Body or Shared
Equipment.
5. Press Left button to exit to main screen.
Schedules (Start/Stop Time) (4/14)
1. Press Menu button > Schedules 4/14 displays.
2. Press Right button to access Schedules menu.
3. Press Up/Down button to select circuit.
4. Press Right button 3 times to select Program 1/1.
5. Press Right button to set Start Time.
6. Press Up/Down button to set time (12 hours).
7. Press Right button to set Stop Time.
8. Press Up/Down button to set time (12 hours).
9. Press Right button to save and exit to main screen.
Edit a Scheduled Program
1. Press Menu button > Schedules 4/14 displays.
2. Press Right button to access Schedules menu.
3. Press Up/Down button to select circuit to edit.
4. Press Right button to select Program to edit (4/4).
5. Press Up/Down button to select Program (2/4).
6. Press Right button 2 times to edit Start Time.
7. Press Up/Down button to adjust Start Time.
8. Press Right button to edit Stop Time.
9. Press Up/Down button to adjust Stop Time.
10. Press Right button to save and exit.
Delete a Scheduled Program
1. Press Menu button > Schedules 4/14 displays.
2. Press Right button to access Schedules menu.
3. Press Up/Down button to select circuit to delete.
4. Press Right button to select Program to delete.
5. Press Up/Down button to select program (2/4).
6. Press Right button to delete a program.
7. Press Up/Down button to select DEL.
8. Press Right button to delete program.
9. Press Left button to exit to main screen.
POOL
/
SPA MODE
1. Press Menu button until Advanced 8/14 displays.
2. Press Right button to access Advanced menu.
3. Press Right button until System Mode displays.
4. Press Up/Down button to select Pool/Spa.
5. Press Right or Left button to exit to main screen.
Set Clock (5/14)
1. Press Menu button until Clock 5/14 is displayed.
2. Press Right button to access Clock menu.
3. Use Right button to select hours/AM,PM and minutes and
Up/Down button adjust time setting.
4. Press Left button to exit.
Setup Valves (Pool, Spa, AUX) (7/14)
1. Press Menu button until Valves 7/14 is displayed.
2. Press Right button to access Valves menu.
3. Press Up/Down button to select circuit (NONE, SPA, POOL,
AUX 1-3, FEATURE 1-4, SOLAR, HEATER, FREEZE).
4. Press Left button to save and exit.
Circuit Functions/Freeze Protect (10/14)
1. Press Menu button > Right button until Cir. Functions
10/14 is displayed.
2. Press Right button to access Cir. Functions menu.
3. Press Up/Down button to select Freeze Protection
for POOL circuit [Yes/No].
4. Press Right button to select Spa circuit.
5. Press Up/Down button to select Freeze Protection
for SPA Circuit [Yes/No].
6. Press Right button to select AUX 1 Circuit.
7. Press Up/Down button to select function for AUX 1 Circuit
[GENERIC, CLEANER, etc.].
8. Press Right button to select Freeze Protection for AUX 1
Circuit.
9. Press Up/Down button to select Freeze Protection for AUX
1 Circuit [Yes/No].
10. Press Right button and repeat Steps 7-9 for Aux 2 & Aux 3
circuits.
11. Press Left button to exit to main screen.
Pool Circuit Function ON/OFF (1/14)
1. Press Menu > Right button to access Circuit On/
Off 1/14 menu.
2. Press Up/Down button to turn Pool lter pump ON or OFF.
Pool circuit ON will display Pool temps on screen.
Set Heat Temp/Select Heat Source (2/14)
1. Press Menu button until Heat 2/14 is displayed.
2. Press Right button: Displays POOL TEMP, POOL HEAT
(OFF/HEATER), SPA TEMP, SPA HEAT, MANUAL HEAT.
3. Use Right button to scroll through above options and Up/
Down button to change setting.
4. Press Left button to exit.
Enable Solar/Heat Pump (6/14)
1. Press Menu button until Solar 6/14 displays.
2. Press Right button to scroll through: Solar Status Enabled
(No/Yes), Heat Start Temp Diff., Heat Stop Diff., Heat
Pump (Yes/No), Cooling (Yes/No), Start Temp, Stop
Temp.
3. Press Up/Down button to change setting.
4. Press Left button to exit.
Air Sensor ON/OFF (8/14)
1. Press Menu button until Advanced 8/14 displays.
2. Press Right button to access Advanced menu.
3. Press Right button to Air Sensor enabled. Press Up/Down
button to disable/enable (NO/YES).
4. Press Left button to exit to main screen.
Note: For “SOLAR ONLY” mode setup instructions,
see back page.
Sanitizer Output Level for Pool and Spa:
Displays the percentage of time chlorine is produced per hour of pump
run time. For example (60%) produces chlorine 60% of the hour; 36
minutes ON, 24 minutes OFF.
4. Press Right button to select POOL Sanitizer Output %.
5. Press Up/Down button adjust Sanitizer Output % for Pool
(0-100%).
6. Press Right button to select SPA Sanitizer Output %.
7. Press Up/Down button adjust Sanitizer Output % for Spa
(0-100%).
Super Chlorination:
Displays the percentage of time chlorine is produced per hour of
pump run time. For example (60%) produces chlorine 60% of the
hour; 36 minutes ON, 24 minutes OFF.
8. Press Right button, select SUPER CHLR.
9. Press Up/Down button, select YES.
10. Press Right button, select RUN HOURS.
11. Press Up/Down button, set hours to run (0-72).
View Super Chlorination Status:
12. Press Right button to view Salt status ppm.
13. Press Left button to exit to main screen.
IntelliChlor
®
Electronic Chlorine Generator(13/14)
1. Press Menu button > IntelliChlor 13/14 displays.
2. Enable IntelliChlor: Press Right button.
3. Press Up/Down button select YES.
SUNTOUCH
®
CONTROL SYSTEM
QUICK REFERENCE GUIDE

Pentair SunTouch Specifications

General

Control Type	Digital
Type	Pool and Spa Control System
Automation	Yes
Display	LCD
Temperature Control	Yes
Programmable	Yes
Application	Pool and Spa
Wireless Remote	Optional
Voltage	120V or 240V
Max Load	Varies by Relay
Power Supply	120V or 240V AC
Load Capacity	Varies by Relay
Weight	5 lbs