PERFECTPRO DIGITUBE - Fm Mode

11 12
GB
GB
2. Press the TUNING or buttonstoselectthedesiredChannelorFrequencyandthentheSELECT-INFO button to tune to
 thechosenfrequency.
3. WhenDABstationsinthetunedchannelarefound,thedisplaywillshowthenameofthestation.Anynewradiostationsfound
will be added to the list stored in the radio.
4. Thesignalstrengthdisplayshowsthereceptionofthestation.Theclearunlledrectangleindicatesminimumsignallevel 
 requiredforsatisfactoryreception.Thesignalstrengthbarswillgoupordownshowingthechangingsignalstrengthasyou
adjust the antenna or the radio position.
5. Repeatstep1to4forotherchannelswithnewstations.
6. Press the MENU button twice to exit manual tuning and return to normal DAB operation.
Dynamic Range Control (DRC) settings – DAB
DRCcanmakequietersoundseasiertohearwhenyourradioisusedinanoisyenvironment.
1. In DAB mode, press the MENU button and the TUNING
or buttons until the display shows “DRC Value”, then press the
SELECT-INFO button .
2. Press the TUNING or buttonstoselectrequiredDRCsetting(defaultisOFF).
 DRCoff DRCisswitchedoff,broadcastDRCwillbeignored.
DRC high DRC is set as sent by broadcaster.
DRC low DRC level is set to 1/2 that sent by broadcaster.
3. Press the SELECT-INFOtheknobtoconrmthesetting.Thedisplaywillreturntonormalradiodisplay.
Note:NotallDABbroadcastsareabletousetheDRCfunction.IfthebroadcastdoesnotsupportDRC,thentheDRCsettinginthe
radiowillhavenoeffect.
Prune stations – DAB
Ifyoumovetoadifferentpartofthecountry,someofthestationsthatwerelistedmaynolongerbeavailable.Also,fromtimeto
time,someDABservicesmaystopbroadcasting,ormaychangelocationorfrequency.ThePrunestationsfunctionwilldeletethe
unavailableDABstationsfromyourstationlist.
1. In DAB mode, press the MENU button and the TUNING or buttons until the display shows “Prune”, then press the
SELECT-INFO button.
2. Press the TUNING or buttonstoselectbetween“Yes”or“No”(defaultisNo).Select“Yes”toenablethisfunctionif
 required,otherwise,select“No”.
3. Press the SELECT-INFObuttontoconrmyoursetting.ThedisplaywillreturntolastmenuandpressMENU to go to the normal
radio display.
Note:Ifyouhavemovedtheradiotoadifferentpartofthecountry,youshouldalsocarryoutasearchfornewstations(pleasesee
thesection“Findingnewstations–DAB”).
FM MODE
Operating the radio – FM seek station
1. Press the On/Off button to switch on the radio.
2. Select the FM RADIO waveband by pressing the SOURCE button.
3. IfthisisthersttimetoswitchtoFMmode,thestationinpreset1willbeplayed.Iftheradiohasbeenusedbefore,thelast
listened station will be played.
4. To seek station, press the TUNING or buttons.Thescanstopsautomaticallywhenitndsastationofsufcientstrength.
5. Afterafewseconds,thedisplaywillupdateandshowstationnameifRDSinformationisbeingreceived.
6. Tondotherstations,presstheTUNING or buttons again.
7. To seek station in an opposite direction, press the TUNING buttontoscanfromlowfrequencytohighfrequencyorpressthe
TUNING buttontoscanfromhighfrequencytolowfrequency.
8. Whenthewavebandendisreached,theradiowillrecommencetuningfromtheoppositewavebandend.
Manual tuning – FM
1. Press the On/Off button to switch on the radio.
2. Select the FM band by pressing the SOURCE button.
3. Press the TUNING or buttonstoreachtherequiredFMstation.Theradiowillchangethefrequencyinstepsof50kHz.
4. Adjusttherubberantennatogetthebestreception.IftheradioistunedtoastationofsufcientsignalstrengthwithRDS 
 informationpresent,thedisplaymaychangetoshowthestationname.
5. Whenthewavebandendisreached,theradiowillrecommencetuningfromtheoppositewavebandend.