Philips 170C6FS/00 User Manual

Horizontal frequencies
30 - 83KHz
Service
Service
Service
TABLE OF CONTENTS
Published by BCU Monitors Printed in Suzhou Copyright reserved Subject to modification S Jun. 16 2005
Description Page
Important Safety Notice ------------------------------2
Technical Data ------------------------------------- 3~4
Front Control & Connections---------------------- 5~6
On-screen Display(OSD)------------------------------7
Factory Mode ----------------------------------------- 8
Aging Mode ------------------------------------------- 9
Pixel Defect Policy------------------------------------10
Smart management --------------------------------- 11
Wiring Message----- ---------------------------------16
Block Diagram----------------------------------------17
Display Adjustments ------------------------------- 12
Mechanical Instructions-------------------------13~14
Safety Test Requirement ---------------------------- 15
Scaler Schematic Diagram & C.B.A ---- -----18~23
Description Page
Control Schematic Diagram & C.B.A. -------------- 24
Power Schematic Diagram & C.B.A ------------25~31
Exploded View--------------------------------------- 32
Spare parts list --------------------------------- -----33
Recommended parts list --------------------------- 34
Warning Message ----------------------------------- 35
Trouble Shooting ------------------------------- 36~37
Repair Tips -------------------------------------- 38~39
Repair Flow Chart ------------------------------ 40~42
ISP Instruction --------------------------------- 43~44
DDC Instructions & Data ---------------------- 45~49
Panel Defect Policy --------------------------------- 50
General Product Specification -----------------51~76
Different Parts List ---------------------------------- 77
Chassis: SH6
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING.
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC
EQUIPMENT CONTAINING HIGH VOLTAGES.
SAFETY NOTICE
GB
3138 106 10474
17 inch TFT LCD Colour Monitor
«
170C6FS/00
170C6FS/93
170C6FS/78

Philips 170C6FS/00 Specifications

General

Brand	Philips
Model	170C6FS/00
Category	Monitor
Language	English

Summary

Important Safety Notice

General Safety Precautions

General guidelines on safe handling and repair practices to minimize risks.

Laser Safety Information

Specific warnings and precautions for servicing products containing lasers.

Technical Data

Pin Assignment

Details the pinout for the 15-pin D-sub connector for signal cable.

Connection to PC

Installing Your LCD Monitor

Guide for physical setup and front/rear view product description.

On Screen Display

The OSD Tree

Visual representation of the OSD menu structure and options.

Factory Mode

Access Factory Mode

Step-by-step guide on how to enter the monitor's factory mode.

Pixel Defect Policy

Pixel Defect Tolerances

Specifies acceptable levels for different types of pixel defects.

Smart Management

SmartControl

Software interface for adjusting monitor performance and viewing hardware info.

Display Adjustment

Alignment procedure

Step-by-step guide for calibrating display alignment using test patterns.

Mechanical Instructions

Step1. Remove the base

Instructions on how to detach the monitor's base.

Safety test requirements

HI-POT TEST INSTRUCTION

Requirements and method for performing Hi-Pot electrical safety testing.

System Block Diagram

Scaler Board Block Diagram

Functional block diagram of the scaler board.

Scaler Schematic Diagram - 1

Control Schematic Diagram & C.B.A

Power Board Block Diagram - Delta

Exploded View

Spare Parts Lists

Mechanical Parts

List of mechanical components with their part numbers.

Warning Message Table

Trouble Shooting

Common Problems

Troubleshooting steps for common issues like 'No Picture' and 'Screen says'.

Repair Tips

1. Servicing of SMDs (Surface Mounted Devices)

Cautions and procedures for handling and soldering Surface Mounted Devices.

Repair Flow Chart

Firmware Upgrade for CPU

System and equipment requirements

Lists necessary hardware and software for the firmware upgrade.

DDC Instructions

DDC Data Re-programming

Explains the process of re-programming DDC IC and main EEPROM.

General Product Specification

2.1 LCD

Specifications related to the LCD panel itself.

TELEVISION/MONITOR SAFFTY GUIDELINES FOR THE PROFESSIONAL SERVICE TECHNICIAN

Safety Checks

Essential safety checks to perform after service to ensure customer safety.

X-radiation

Safety measures to prevent X-radiation exposure during service.

Leakage Current Hot Check

Procedure for checking AC leakage current with the unit plugged in.