Section
lID
(Operating this unit
1 Touch
CLOCK
ADJ
on
the
system menu.
2 Touch ON/OFF
to
turn
the
clock display
on.
•
To
turn the clock display
off,
touch ON/OFF
again.
3 Touch
....
or
~
to
select
the
segment
of
the
clock display you wish
to
set.
Each
time
you
touch
....
or
~
it will select one
segment
of the
clock
display:
Hour-Minute
As you select
segments
of
the
clock display
the
segment
selected will
be
highlighted.
4 Touch
...
or
~
to
put
a clock right.
• Notes
•
You
can match the clock to a time signal
by
touching
JUST.
-
If
00
to
29, the minutes
are
rounded down.
(e.g.,
10:18 becomes 10:00.)
-
If
30
to
59, the minutes
are
rounded
up.
(e.g.,
10:36 becomes 11:00.)
•
Even
when the sources
are
off,
the clock dis-
play appears
on
the display.
Setting
for
rear
view
camera
(back
up
camera)
4
CAUTION
Pioneer
recommends
the
use
of
a
camera
which
outputs
mirror reversed images, other-
wise
screen
image
may
appear
reversed.
This
unit
features a
function
that
automatically
switches to
the
rear view
camera
video
(REAR
CAMERA IN jack)
when
a rear view camera is
installed on
your
vehicle. When the gear
shift
is
in REVERSE (R) position, the video auto-
matically
switches
to a rear view
camera
video. (For
more
details,
consult
your dealer.)
•
After
you set up the rear view camera set-
ting, move
the
gear
shift
in
REVERSE (R)
and
confirm
if a rear view camera video
can
be
shown
on the display.
• If the display
should
be switched to a rear
view
camera
video by error
while
you are
@
En
)
driving forward, change the rear view cam-
era setting.
•
To
end
watching
a rear view
camera
video
and return
to
the source display, press and
hold
VOLUME/MUTE.
•
Even
while
driving, rear view
camera
image
can
be
displayed.
To
do this,
touch
REARVIEW source icon.
In
this
case.
touch
REARVIEW again to
turn
off the rear view
camera. For details, refer
to
Selecting a
source
on page
16.
• Touch CAMERA POLARITY on
the
sys-
tem
menu
to
select an appropriate setting.
•
BATTERY
- When the polarity of the con-
nected
lead
is
positive while the gear shift
is
in
REVERSE (R) position
• GROUND - When the polarity of the con-
nected
lead
is
negative while the gear shift
is
In
REVERSE (R) position
•
OFF
- When a rear view camera
is
not con-
nected to th
is
unit
Adjusting
the
LCD
panel
slide
position
You
can adj ust the LCD panel
sl
ide position
so
that
the panel is set back
or
forward.
1 Touch NEXT on
the
system menu.
2 Touch
FLAP
SET
BACK
to
turn
the
set
back on.
The LCD panel slides
to
the back.
•
Touch
FLAP
SET
BACK
again to turn the set
back off and the
LCD
panel slides to the front.
Setti
ng
the
automatic
open
function
To
prevent the display
from
hitting
the
shift
lever of an
automatic
vehicle when it is
In
P
(park) position,
or
when you do not
wish
the
display
to
open/close automatically, you can
set the
automatic
open
function
in
the
manual
mode.
1 Touch NEXT on
the
system menu.
To Next Page
Loading...
Need help?
General
