Section
r:D
(Operating this
unit
5
Press
EQ
to
proceed
to
the
16-point ad-
justment.
The 16-point
touch
panel
adjustment
screen
appears,
•
To
cancel the adjustment. press and hold
VOLUME/MUTE,
6 Gently touch
the
center
of
the
+ mark
displayed on
the
screen
with
the
touch
panel adjustment pen.
After
you
touch
all the marks, the adjusted po-
sition data is saved,
•
Do
not turn off the engine whi
Ie
saving the
ad-
justed position data,
7
Press
and hold VOLUME/MUTE
to
com-
plete
the
adjustment.
Using
the
AUX
source
A separately sold auxiliary device
such
as
VCR
or
portable device can
be
connected to
this
unit. When connected, auxiliary device is auto-
matically recognized as AUX source and
as-
signed
to
AUX.
About
AUX
connection
method
You
have
two
methods to
connect
auxiliary de-
vice
to
this
unit.
Mini
pin
plug
cable (AUX 1)
When
connecting auxiliary device
using
a
mini
plug cable
iPod and portable audio/video player can
be
connected to
this
unit
via mini plug cable,
• If an iPod with video capabilities is con-
nected
to
this
unit
via
3,5
mm
plug
(4
pole)
cable
(e,g"
CD-V150M), you can enjoy the
video
contents
of the iPod,
• It is possible
to
connect
a portable
audio/
video player
by
using a
3,5
mm
plug
(4
pole) to RCA cable,
which
is
sold sepa-
rately, However, depending on the cable,
re-
verse
connection
between
Red
(right side
audio) cable and yellow (video) cable is
re-
quired, Otherwise, audio and video may
not
be
correctly reproduced,
@
En
)
• Insert
the
mini plug into
the
AUX
input
jack on this unit.
For more details, refer
to
What's What on page
15,
IP-BUS-RCA
interconnector
(AUX 2)
When
connecting auxiliary device
using
an
IP
BUS-RCA Interconnector (sold separately)
•
Use
an IP-BUS-RCA Interconnector
such
as
the
CD-RB20/CD-RB10 (sold separetely)
to
connect this unit
to
auxiliary device fea-
turing
RCA
output.
For more detai
Is,
refer to the IP-BUS-RCA Inter-
connector
owner's
manual,
•
You
can only make this type of connection if
the
auxi
Iiary device
has
RCA
outputs,
Selecting AUX as
the
source
• Touch
the
source icon and then touch
AUX
1/AUX
2
to
select
AUX
as
the
source.
•
If
the auxiliary setting
is
not turned on, AUX
cannot
be
selected,
For
more details,
see
Switch-
ing the auxiliary setting
on page
41
,
Setting
the
AUX
title
The title displayed
for
the
AUX
source can
be
changed,
• Each
title
can
be
up
to
10
characters
long,
1
After
you have selected AUX
as
the
source, touch AV MENU and
FUNGION
MENU and then touch
NAME EDIT.
• When the touch panel
keys
are not displayed,
you
can display them
by
touching the screen,
2 Touch
ABC
to
select
the
desired charac-
ter
type.
Touch
ABC
repeatedly
to
switch between the
following
character
types:
Alphabet
(upper
case)-Alphabet
(lower case)
-European
letters, such as those
with
ac-
cents
(e,g"
ii,
ii,
a,
~)
•
You
can select to input numbers and symbols
by
touching
123,
To Next Page
Loading...
Need help?
General
