Pioneer SC-LX58 User Manual

86
Using other functions
09
Resetting the system
Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.
Set MULTI-ZONE to MULTI ZONE OFF.
! Disconnect the iPod and USB memory device from the receiver beforehand.
! Set the Control with HDMI to OFF (see HDMI Setup on page 74 ).
1 Switch the receiver into standby.
2 While holding down ENTER on the front panel, press u STANDBY/ON.
The display shows RESET c NO d.
3 Select ‘RESET’ using PRESET k/l, then press ENTER on the front panel.
The display shows RESET? OK.
4 Press ENTER to confirm.
OK appears in the display to indicate that the receiver has been reset to the factory default settings.
! Note that all settings will be saved, even if the receiver is unplugged.
Default system settings
Setting Default
Digital Video Converter
OFF
SPEAKERS
TMd/FW ON
Speaker System
7.2.2ch TMd/FW
Speaker Setting
Front
SMALL
Center
SMALL
TMd/TFw/TBw
SMALL
FH/FW
SMALL
Surr
SMALL
SB
SMALLx2
SW
SW1+2 YES
Surround Position
ON SIDE
Crossover
80Hz
X-Curve
OFF
DIMMER Medium bright
Inputs
See Input function default and possible settings on page 50 .
Input Volume Absorber All Inputs
0dB
HDMI
HDMI Audio
AMP
Control
OFF
Control Mode --- (OFF)
ARC (Audio Return Channel) --- (OFF)
PQLS --- (AUTO)
Standby Through
OFF
4K/60p
4:4:4
DSP
Power On Level
LAST
Setting Default
Volume Limit
OFF
Mute Level
FULL
Phase Control
ON
Auto Sound Retriever
iPod/USB, INTERNET RADIO, MEDIA
SERVER, FAVORITES, BT AUDIO input
function
ON
Other input functions
OFF
Sound Delay 0 ms
Dual Mono
CH1
DRC
OFF
LFE Attenuate
0dB
Auto delay
OFF
Digital Safety
OFF
Effect Level ALC (Auto Level Control)
50
Center Spread
Input with video image
OFF
Input without video image
ON
Neo:X Options Center Gain
Neo:X CINEMA: 1.0
Neo:X MUSIC: 0.3
Neo:X GAME: 1.0
All Inputs
Listening Mode (2 ch/multi ch)
AUTO SURROUND
Listening Mode (Headphones)
STEREO
See also Setting the Audio options on page 78 for other default DSP settings.
MCACC
MCACC Position Memory
M1. MEMORY 1
Channel Level (M1 to M6) 0.0 dB
Speaker Distance (M1 to M6) 3.00 m
Standing Wave (M1 to M6)
ATT of all channels/filters 0.0 dB
SWch Wide Trim 0.0 dB
EQ Data (M1 to M6)
All channels/bands 0.0 dB
EQ Wide Trim 0.0 dB
Network
Network Standby
OFF
DHCP
ON

Pioneer SC-LX58 Specifications

General

Receiver type	Surround
Output impedance	4 Ω
Pre-out channels	9.2
Input sensitivity	390 mV
Pre-out connectivity	Yes
Audio output channels	9.2 channels
Audio A/D Converter (ADC)	24-bit/192kHz
Signal-to-Noise Ratio (SNR)	101 dB
Power output per channel (1KHz@6 Ohm)	190 W
Power output per channel (20-20KHz@8 Ohm)	240 W
HDMI in	8
Ethernet LAN (RJ-45) ports	1
Component video (YPbPr/YCbCr) in	2
Number of HDMI outputs	3
Speakers connectivity type	-
Supported radio bands	AM, FM
Preset stations quantity	63
Internet radio services supported	Spotify, vTuner
Optical drive included	No
Product color	Silver
Audio decoders	Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS Neo:X, DTS-ES, DTS-HD Master Audio
Graphical user interface (GUI) language	Dutch, English, French, German, Italian, Russian, Spanish
AC input voltage	220-230 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	330 W

Weight and Dimensions

Depth	441 mm
Width	435 mm
Height	185 mm
Weight	15300 g