9
01
Before you start
Operating range of remote control unit
The remote control may not work properly if:
! There are obstacles between the remote control and the receiver’s remote sensor.
! Direct sunlight or fluorescent light is shining onto the remote sensor.
! The receiver is located near a device that is emitting infrared rays.
! The receiver is operated simultaneously with another infrared remote control unit.
30°
30°
7 m
Selecting the OSD character set
Select the character set to be used for displaying the receiver’s OSD. When ‘Latin’ is selected, English, French,
German, Italian, Spanish, Dutch and Russian can be selected for the OSD Language setting (page 45). When
‘Chinese’ is selected, Chinese becomes selectable for the OSD Language setting (page 45).
To change the OSD character set, perform the operations on the front panel. When using the multi-zone function,
set MULTI ZONE OFF before performing the operations below.
1 Switch the receiver into standby.
2 While holding down ENTER on the front panel, press u STANDBY/ON.
The display shows RESET c NO d.
3 Select ‘FONT’ using TUNE i/j.
4 Use PRESET k/l to select ‘Latin’ or ‘Chinese’ then press ENTER on the front panel.
The display shows CHANGE? [OK].
5 Press ENTER to confirm.
‘OK’ is displayed and the receiver automatically restarts.
To change the OSD language to something other than English, change the OSD Language setting. For details,
see Changing the OSD display language (OSD Language) on page 45.
About using AVNavigator (included CD-ROM)
The included AVNavigator CD-ROM contains Wiring Navi allowing you to easily make the receiver’s connections
and initial settings in dialog fashion. High precision initial settings can be completed easily simply by following
the instructions on the screen to make the connections and settings.
There are also other features enabling easy use of various functions, including an Interactive Manual that oper-
ates in association with the receiver, updating of various types of software, and MCACC Application that lets you
check the MCACC measurement results on 3D graphs.
Installing AVNavigator
1 Load the included CD-ROM into your computer’s CD drive.
The CD-ROM’s top menu screen appears.
2 Click ‘Install AVNavigator’ from the CD-ROM top menu.
3 Follow the instructions on the screen to install.
When “Finish” is selected, installation is completed.
4 Remove the included CD-ROM from the computer’s CD drive.
Handling the CD-ROM
Operating Environment
! AVNavigator can be used with Microsoft
®
Windows
®
XP/Vista/7.
! A browser is at times used for AVNavigator functions. The supported browser is Microsoft Internet Explorer 8
or 9.
! Adobe
®
Flash
®
Player 10 must be installed to use some of the functions in AVNavigator.
For details, see http://www.adobe.com/downloads/.
Precautions For Use
! This CD-ROM is for use with a personal computer. It cannot be used with a DVD player or music CD player.
Attempting to play this CD-ROM with a DVD player or music CD player can damage speakers or cause
impaired hearing due to the large volume.
License
! Please agree to the “Terms of Use” indicated below before using this CD-ROM. Do not use if you are unwilling
to consent to the terms of its use.
Terms of Use
! Copyright to data provided on this CD-ROM belongs to PIONEER CORPORATION. Unauthorized transfer,
duplication, broadcast, public transmission, translation, sales, lending or other such matters that go beyond
the scope of “personal use” or “citation” as defined by Copyright Law may be subject to punitive actions.
Permission to use this CD-ROM is granted under license by PIONEER CORPORATION.
General Disclaimer
! PIONEER CORPORATION does not guarantee the operation of this CD-ROM with respect to personal com-
puters using any of the applicable OS. In addition, PIONEER CORPORATION is not liable for any damages
incurred as a result of use of this CD-ROM and is not responsible for any compensation. The names of private
corporations, products and other entities described herein are the registered trademarks or trademarks of their
respective firms.
To Next Page
Loading...
Need help?
General
