What does "ErP" Error Code mean on Pit Boss Grill?
If your Pit Boss Grill displays an "ErP" error code, it means the unit wasn't turned off properly the last time it was connected to power. To fix this, press the Power Button to turn the unit off, wait two minutes, and then press the Power Button again to turn it back on.
How to lower the temperature on the SMOKE setting of my Pit Boss 71700FB Grill?
If the grill temperature on the SMOKE setting is too high on your Pit Boss grill, the "P" setting might be too low. To adjust this, turn the temperature dial to SMOKE, push the "P" SET button, and increase the "P" setting. Keep in mind that after preheating at high heat, the auger will continuously feed pellets for four minutes, raising the temperature temporarily. It will stabilize once the "P" setting cycle begins (approximately five to ten minutes).
Why Pit Boss 71700FB will not achieve or maintain stable temperature?
If your Pit Boss Grill isn't reaching or maintaining a stable temperature, here are some things to check: * **Airflow:** Make sure there isn't ash build-up or any obstructions in the fire pot. * **Fuel:** Ensure the hopper has enough fuel and that the fuel is of good quality. Also, check for any obstructions in the feed system. * **Temperature Probe:** Check the status of the temperature probe and clean it if it's dirty.
How to adjust Pit Boss Grill temperature when SMOKE is too high?
If the grill temperature on the SMOKE setting is too high on your Pit Boss Grill, push the "P" SET button and increase the "P" setting.
Why won't the LCD screen light up on my Pit Boss 71700FB?
There are several reasons why the LCD screen on your Pit Boss grill might not be lighting up. First, ensure the grill is properly plugged into a working power source. Also, check that all wire connections are firmly connected. Another possible cause is a blown fuse on the circuit board, which would need to be replaced. The GFCI outlet may have been tripped, so ensure it's a minimum 10 Amp service and the wire connections are dry. Finally, make sure the temperature dial is not in the OFF position; turn it to SMOKE to start the unit.
What does "Er1" Error Code mean on Pit Boss 71700FB Grill?
If you're seeing an "Er1" error code on your Pit Boss Grill, it indicates that the temperature probe wire isn't making a connection. Remove the hopper access panel and check for any damage to the temperature probe wires.
What to do if Pit Boss 71700FB Grill temperature is flashing on LCD screen?
If the temperature is flashing on the LCD screen of your Pit Boss Grill, check the hopper for sufficient fuel or if there is an obstruction in the feed system. Remove pellets and follow Care and Maintenance instructions.
What does "ErH" Error Code mean on Pit Boss Grill?
If you receive an "ErH" error code on your Pit Boss Grill, it indicates that the unit has overheated, possibly due to a grease fire or excess fuel. To resolve this, press the Power Button to turn the unit off and allow the grill to cool. Follow the Care and Maintenance instructions. After maintenance, remove the pellets and confirm the correct positioning of all component parts.
How to prevent frequent flare-ups on my Pit Boss 71700FB Grill?
To prevent frequent flare-ups on your Pit Boss grill, try cooking at a lower temperature. Grease has a flash point, so keeping the temperature under 176°C / 350°F when cooking greasy foods can help.
What does "ErP" mean on a Pit Boss 71700FB?
The "ErP" error message on your Pit Boss grill can occur if the temperature dial wasn't in the OFF position when last connected to AC power. To fix this, turn the temperature dial to OFF, wait two minutes, and then turn the unit back on to SMOKE or your desired temperature. This safety feature prevents an inadvertent start. This error can also appear if a power outage occurred while in operation, but there is no suggested solution to fix this.
Introduction to the assembly process and operational guidelines for the wood pellet grill.
Critical safety precautions, hazards, and warnings for operating the grill.
Guidance on connecting the grill to a suitable power source.
Explanation of temperature settings and general cooking advice.
Details on the warranty terms, duration, and what is covered.
General| Temperature Range | 180°F to 500°F |
|---|---|
| Warranty | 5 years |
| Fuel Type | Wood pellets |
| Wheels | 2 |
| Ignition Type | Electric |
| Type | Pellet grill |
| Cooking Area | 700 sq. in. |
| Primary Cooking Grid Material | Porcelain-coated steel |
To Next Page