To Previous Page

9 10

ASME COMPLIANT SUCTION FITTING INFO

PSF-100A AND PSF-100B SUCTION OUTLET

FOR ABOVE GROUND POOL

IMPORTANT SAFETY INSTRUCTIONS

(1) READ AND FOLLOW ALL INSTRUCTIONS

CAUTION! DO NOT EXCEED THE MAXIMUM ALLOWABLE FLOW RATE:

READ, THEN KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

(1) PSF-100A and PSF-100B Suction Outlets are certified by IAPMO in accordance with the ASME/ANSI A112.19.8b-

2009 Suction Fitting for use in Swimming Pools, Wading Pools, Spas, and Hot Tubs.

(2) This is a submerged suction outlet for use with above ground swimming pool.

(3) For single drain only. Use only ONE outlet for each pump.

(4) Do not locate this suction outlet on sitting areas or on the backrest for such seating area.

(5) Install this outlet at location recommended by the pool manufacturer.

(6) The maximum allowable flow rate of this suction outlet is 45 gallon per minute (2,700 gallonper hour).

(7) Connection Hose:

• Model PSF-100-A is to be connected with 1 1/4” (31.8mm) diameter hose.

• Model PSF-100-B is to be connected with 1 1/2” (38.1mm) diameter hose.

(8) The suction outlet is to be mounted at the suction outlet opening as specified by the manufacturer of the

above ground pool. The diameter of this opening should be within the range of 1.77” to 1.85” (45.0mm to

47.0mm). Refer to the following diagram for detail assembly instructions:

(9) The suction outlet PSF-100A or PSF-100B is to be replace every 5 years.

(10) No tool is required for installation.

(11) Service and Winterizing Instructions

• 45 Gallon per minute (2,700 Gallon per hour).

• Carefully observe and inspect the suction outlet for damage and tampering before each use of the pool.

• Missing, broken or cracked suction outlet must be replaced before using the pool.

• Loose suction fitting should be reattached or replaced before using the pool.

• Remove and store Suction Outlet assembly if temperatures are expected to fall below 32° F.

Swimming Pool

Connect To The Intake

Of Filter Pump

Water Hose

Hose Clamp

Lock Nut, To Be Tightened By Hand

Fitting Opening, 45-47mm Diameter

Suction Fitting, PSF-100A Or PSF-100B

Rubber Gasket

Water Cap, To Be Installed Only During

Pump Maintenance Or Filter Change

Flat Washer

PART LIST

Pump Body With Cord & GFCI

096-050406

096-050504

096-050564

Rotor Assembly

096-110003

096-050505

096-050598

096-050565

Pump Gasket

078-110031

078-110078

Volute Housing

078-110189

078-110097

078-110147

O-Ring (On Volute Housing)

090-130012

090-130025

Phillips Head Screw (6 EA)

090-010063

Assembled Pump #1 THRU #6

096-050610

096-050609

096-050608

096-050607

Pump R

etaining Nut

078-110143

Filter Case

078-110100

078-110114

078-110139

Seal Top

078-110101

078-110140

Seal Top Retainer

078-110102

Vent Screw

078-110103

Suction Hose 3 FT.

063-060010

Return Hose 3 FT.

063-060010

Hose Clamp

090-160005

059910-250450-00PR01-1

059910-250

450-00PR01-1

8" Filter Cartridge

R-P52-0002

Suction Fitting (SF)

078-110284

SF Gasket (Black)

078-110123

SF Thrust Washer (White)

078-110124

SF Nut

078-110125

SF Water Cap

078-110282

RF Plug

078-110126

O-Ring (On Filter Case)

090-130022

090-130

022

090-130022

O-Ring (On Vent Screw)

090-130021

O-Ring (On Hose Connection)

090-130030

Return Fitting (RF)

078-201401

RF Gasket (Black)

078-201402

RF Nut

090-201401

RF Diverter Fitting

078-201408

Assembled Filter #1 THRU #28

096-201403

096-201404

096-201405

096-201406

RP800/F700C RP1000/F1000C RP1000/F1500C RP2000/F2000C

Key# Description

Part #

Qty.

1 X1

2 X1

3 X1

4 X1

5 X1

6 X1

* X1

7 X1

8 X1

9 X1

10 X1

11 X1

12 X1

13 X1

14 X4

15 X1

16 X1

17 X1

18 X1

19 X1

20 X1

21 X1

22 X1

23 X1

24 X4

25 X1

26 X1

27 X1

28 X1

29 X1

Brand	Polygroup
Model	Quick Set Pool
Category	Swimming Pool
Language	English

Polygroup Quick Set Pool User Manual

Table of Contents

Questions and Answers:

Polygroup Quick Set Pool Specifications

Related product manuals