Polytec PSV 300 - Page 101

 

        
over voltage protection, interfaces junctionover voltage protection, interfaces junction
boxbox
7-57-5
OVER, indicator on the controllerOVER, indicator on the controller
3-43-4
overrange indicatoroverrange indicator
in the softwarein the software
5-85-8
on the controlleron the controller
5-85-8

pan-tilt stagepan-tilt stage
assembly on the tripodassembly on the tripod 3-183-18
cablingcabling 3-273-27
operating requirementsoperating requirements 3-13-1
setting up the scanning headsetting up the scanning head 5-25-2
technical specificationtechnical specification 7-117-11
phase difference, theoryphase difference, theory B-1B-1
phase response, specificationphase response, specification 7-37-3
phase roll-off, specificphase roll-off, specific 7-37-3
phase shift, caused by the velocity decoderphase shift, caused by the velocity decoder 4-74-7
PLL decoderPLL decoder
C-4C-4
pointing stability, scannerpointing stability, scanner
7-87-8
position, of laser warning labelsposition, of laser warning labels
in EC countriesin EC countries
1-21-2
in non-EC countriesin non-EC countries
1-31-3
positioning, the laser beampositioning, the laser beam
in the softwarein the software
5-65-6
using hand set using hand set PSV-ZPSV-Z-051-051
5-55-5
POWERPOWER
LED on the controllerLED on the controller 3-33-3
LED on the LED on the junction box model -junction box model -FF, -U, -U 3-93-9
LED on the junction box model -HLED on the junction box model -H 3-83-8
LED on the workstationLED on the workstation 3-123-12
power consumptionpower consumption
controllercontroller 7-17-1
junction boxjunction box 7-57-5
pan-tilt stagepan-tilt stage 7-117-11
scanning headscanning head 7-77-7
workstationworkstation 7-107-10
preparing, functional testpreparing, functional test
3-283-28
PRINTER, connectorPRINTER, connector
on the workstation model on the workstation model -F-F, -U, -U 3-163-16
on the workstation model -Hon the workstation model -H 3-143-14
processor, workstationprocessor, workstation 7-107-10
protection classprotection class
controllercontroller
7-17-1
junction boxjunction box
7-57-5
PSVPSV
modelsmodels
2-22-2
start-upstart-up
4-14-1

REFREF
jack on the junction box model -Fjack on the junction box model -F, -U, -U 3-103-10
REF1, REF2, REF3REF1, REF2, REF3
jack on the junction box model -Hjack on the junction box model -H 3-93-9
reference signal, cablingreference signal, cabling 3-223-22
REMOTE CONTROL, jack on the scanningREMOTE CONTROL, jack on the scanning
headhead
3-63-6
REMOTE FOCUS, interface on the controllerREMOTE FOCUS, interface on the controller
3-63-6
REMOTE, LED on the controllerREMOTE, LED on the controller
3-43-4
RESETRESET
key on the controllerkey on the controller
3-43-4
key on the workstationkey on the workstation
3-123-12
resolutionresolution
7-27-2
return, the PSVreturn, the PSV
3-23-2
RF signal conditioning, in the controllerRF signal conditioning, in the controller
C-2C-2
ring light, for micro scan lensesring light, for micro scan lenses A-5A-5
rotation velocity, pan-tilt stagerotation velocity, pan-tilt stage 7-117-11
RS-232 interfaceRS-232 interface
on the controlleron the controller 3-53-5
on the junction boxon the junction box 3-113-11

safetysafety
electricalelectrical 1-41-4
laserlaser
1-11-1
scaling factorscaling factor
7-27-2
scan angle, close-up unitscan angle, close-up unit
A-1A-1
scan fieldsscan fields
close-up lensesclose-up lenses
A-2A-2
micro scan lensesmicro scan lenses
A-4A-4
scan points, definingscan points, defining
in the softwarein the software
5-85-8
using hand set using hand set PSVPSV-Z-051-Z-051
5-75-7
scan points, deletingscan points, deleting
in the softwarein the software 5-85-8
using hand set using hand set PSVPSV-Z-051-Z-051 5-85-8
scanner typescanner type 7-87-8
scanner, specificationscanner, specification 7-87-8