All system components should now be correctly mounted.All system components should now be correctly mounted.
The individual steps on cabling the The individual steps on cabling the PSV are described in the following. ThePSV are described in the following. The
complete cabling is shown incomplete cabling is shown infig
figureure 3.13.166totofigfigururee 3.13.188. All connections must. All connections must
be made easily. If not, check the plugs for bent contact pins to avoid seriousbe made easily. If not, check the plugs for bent contact pins to avoid serious
damage being incurred. Secure the connections correspondingly. Should anydamage being incurred. Secure the connections correspondingly. Should any
problems occur in cabling, please contact your local Polytec representative.problems occur in cabling, please contact your local Polytec representative.
1.1. ConneConnect the kect the keyboayboard to the sord to the socket Kcket KEYBEYBOAROARD on the back oD on the back of thef the
workstation.workstation.
2.2. ConneConnect the moct the mouse to the suse to the sockeocket MOUt MOUSE on thSE on the back of the back of the worke workstatstation.ion.
3.3. Plug tPlug the monihe monitor cabtor cable into tle into the back ohe back of the monif the monitor and intor and into the socto the socketket
MONITOR on the back of the workstation.MONITOR on the back of the workstation.
⇔⇔
4.4. TTo operao operate the cte the controntroller voller via the sia the softoftwareware, plug a, plug ann
cable into thecable into the
jack jack RS 23RS 232 on 2 on the the back back of tof the cohe controntroller ller and iand into nto eitheither oer of the f the jackjackss
COM1 or COM2 on the back of the workstation.COM1 or COM2 on the back of the workstation.
⇔⇔
5.5. If applIf applicablicable, conne, connect the optect the optional haional hand set OFVnd set OFV-310 to the ci-310 to the circularcular jackr jack
REMOTE FOCUS on the back of the controller.REMOTE FOCUS on the back of the controller.
⇔⇔
66.. PPlluug g tthhee
cable into the Sub-D jack INTERFEROMETERcable into the Sub-D jack INTERFEROMETER
on the back of the controllon the back of the controller and into the Sub-D jack VIBROMETER on theer and into the Sub-D jack VIBROMETER on the
back of the junction box.back of the junction box.
7.7. For tFor transmransmissiission of ton of the velhe velocitocity sigy signal, nal, plug tplug thehe
cable into the BNCcable into the BNC
jack jack VELOCVELOCITY OITY OUTPUUTPUT on T on the the fronfront of t of the cthe controontroller ller and iand into nto the the BNCBNC
jack jack VELO oVELO on the n the fronfront of t of the the juncjunction tion box.box.
8.8. If required, connect the reference signal to the BNC jackIf required, connect the reference signal to the BNC jack
REFREF1 on the front of the junction box for the model -H.1 on the front of the junction box for the model -H.
If required, connect the reference signal to the BNC jackIf required, connect the reference signal to the BNC jack
REF on the front of the junction box for the models -F REF on the front of the junction box for the models -F and -U.and -U.
9.9.
You can connect two additional reference signals to theYou can connect two additional reference signals to the
BNC jacks REBNC jacks REFF2 and REF2 and REF3 on the front of the junction box for the model3 on the front of the junction box for the model
-H.-H.
10.10. If required, connect thIf required, connect the external trigger signal to te external trigger signal to the BNC jack TRIhe BNC jack TRIG IN onG IN on
the front of the junction box.the front of the junction box.
connect all components to each otherconnect all components to each other
plugging in the mains cables!plugging in the mains cables!
To Next Page
Loading...
