Poulan Pro P3314WSA User Manual

AwnnrutruC:
The
charn
musr
nor
move when
the engine
runs at idle speed.
lf
the chain
moves at
idle speed
refer to CAR
BURETOR
ADJUSTIVIENT
within this
manual. Avoid conlact
with the
muffler. A hot
mutfler can cause
serious
burns.
To
stop
the engine
move the ONiSTOP
switch to
the
STOP
position.
To start the engine
hold the saw
firmly on
the
ground
as
illustrated. Make
sure the chatn
rs
free to turn
without contacting any
object.
Use only
15
-
lB"
(40
-
45 cm) of
rope
per puil.
Hold saw
firmly whtle
pulhnq
starteroop
Starter
Fope Handle
Left
Hand
on
Front
Handle
Right
Foot Through
Rear Handle
A
wnnrutruc:
Do
notatremptrorhrow
or drop- slart
the charn saw.
Doing so wtll
put
the operator at
risk of serious
inJUry due to
loss of control of
the chain saw.
IMPORTANT
POINTS
TO REMEMBER
When
pulling
the starter
rope, do
not use the
full extent of
the rope as
this can cause
the
rope to break.
Do not
let
starter
rope snap
back
Hold the handle and
let the
rope re
wrnd
slowly.
For cold weather
starting, start
the untl at
FULL CHOKE: allow
the englne
to warm up
before
squeezing
lhe lhrott e
lrigger.
NOTE:
Oo not attempt
to cut
material with
the choke/fast
idle lever in the
FU LL
CHOKE
posrtron.
HELPFUL
TIP
lf
your
engine
still does
not
start
after
following these
instructionf
please
call
1
-800-554-6723.
STARTING
A
COLD
ENGINE
(orwarm
engine after
running out of
fuel)
NOTE: In the
following steps.
when the
choke/fast
idle lever
is
pulled
out to
the full
extent, the correct
throltle
settinq
{or
startrnq
is
set
automatrcallV.
1 Move Of.r ifOp
swrtch to
the oN
posl
tron.
2
Slowly
press
pr
mer bulb 6
times.
3
Pull choke/fast
idle lever out to
the full
extent
(to
the FULL CHOKE
position)
4. Pull the starter
rope sharply 5
times
wrth
your
right hand. Then,
proceed to the
nexl
step.
NOTE: lf the engine
sounds as
if it is trying
to start
before the 5th
pull.
slop
pulling
and
immedialely
proceed
to the next s1ep.
5.
Push the choke/fast
idle
lever in to the
HALF CHOKE
position.
CHOKE/FAST
IDLE LEVER
HALF
FULL
V;
"o'
\\-
\
UNOKE
Lever
right hand until the engrne
starts.
Allow the engrne
to run for approximate
ly 30 seconds.
Then, squeeze
and
re-
ease
ll-c l"rroltle
lrigger to allow
engine
IGNITION
SWITCH
ON
6
7
7
Pull the sta(er
rope sharply
wtth
youl
to
return to
rdle
speed.
STARTING
A WARM ENGINE
1. Move ONiSTOP swrtch
to the ON
posi
tron.
2. Slow
y
press pr
mer
bulb
6 trmes.
3
To set
the fast idle.
pull
the
chokelfast
idle lever out to the
full
extent
(to
the full
choke
posrtron):
then
push
the
lever
back
n to the HALF CHOKE
pos
trorr
4
Pull the starter
rope sharply
wrttr
yoLlr
rlght
hand untr the er.rq
ne starts
5. Squeeze
and
re ease throttle
tr
gger
to
allow eng
ne 10
relurn to d e speed.
DIFFICULT STARTING
(or
starting
a
flooded engine)
The engine
may be
flooded with too
much
fuel if it has
nol
started
after
10
pulls.
Flooded
engines can
be cleared of excess
{uel by
prrshrng
lne c.-roheiasl
role
lever
in com
pletely
(to
the OFF CHOKE
position)
and
then followrng
the warm engtne
startlng
pro-
cedure
listecl
above.
Ensure
the ON/STOP
switch
is in the ON
position.
l
-P-xr
''
\:
10

Poulan Pro P3314WSA Specifications

General

Brand	Poulan Pro
Model	P3314WSA
Category	Chainsaw
Language	English