PowerBass AutoSound ASA 200.2x User Manual

PowerBass AutoSound ASA 200.2x

24 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

ASA SERIES CLASS A/B AMPLIFIER

Owners Manual

Please read through this manual to familiarize yourself with your new ampliﬁ er. Should your PowerBass

AutoSound mobile ampliﬁ er ever require service, you will need to have the original dated receipt.

ASA 400.4x

ASA 600.4x

ASA 700.5x

ASA 1100.5x

ASA 200.2x

ASA 300.2x

ASA 400.2x

ASA 600.2x

ASA 800.2x

Table of Contents

Questions and Answers:

H
Herbert GilbertAug 12, 2025
What to do if the PowerBass AutoSound ASA 200.2x Amplifier red status protection LED is ON and there is no output?
- M
  Melinda ChambersAug 12, 2025
  If the red status protection LED is on and there's no output, it could be due to several reasons: * Thermal protection: Ensure proper impedance at the speaker terminals and check for adequate airflow around the amplifier. * Voltage protection: The voltage to the amplifier may not be within the 10-16 VDC operating range. Inspect the battery/charging system. * Short circuit protection: Inspect speaker wires for shorts to each other or the vehicle chassis. Speakers operating below the minimum impedance can also trigger this.
O
ostevensAug 19, 2025
How to fix alternator noise that varies with RPM in my PowerBass AutoSound ASA 200.2x?
- J
  Joseph Butler MDAug 19, 2025
  To address alternator noise that changes with RPM, check the following: * Inspect the RCA cable for damage. * Verify the routing of the RCA cable. * Ensure the source unit has a good ground. * Check the amplifier's gain setting; reduce it if it's set too high.
F
Frederick GillAug 27, 2025
What to do if the Power LED on my PowerBass Amplifier is not ON?
- C
  Charlene WagnerAug 27, 2025
  If the power LED is not on, use a Volt Ohm Meter (VOM) to check: * The +12 Volt power terminal (it should read +12 to +16VDC). * The remote turn-on terminal (it should read +12 to +16VDC). * The ground terminal.
M
Mr. Jonathan SnowSep 3, 2025
What to do if my PowerBass Amplifier Power LED lights GREEN, but there is no output?
- A
  Alison JacksonSep 4, 2025
  If the power LED lights green but there is no output, you should: * Check the RCA connections. * Test the speaker outputs with a known good speaker. * Substitute a known good source unit. * Check for a signal on the RCA cable with a VOM in AC position.

PowerBass AutoSound ASA 200.2x Specifications

General

Channels	2
RMS Power @ 2 Ohms	100W x 2
Bridged RMS Power @ 4 Ohms	200W x 1
Total Harmonic Distortion (THD)	<0.05%
Signal-to-Noise Ratio	>90dB
Input Sensitivity	200mV - 6V
THD at Rated Power	<0.05%
Damping Factor	>200
Crossover Slope	12dB/octave
Low Pass Crossover	50Hz - 250Hz
High Pass Crossover	50Hz - 250Hz
Bass Boost	0 - 12 dB
Bass Boost Frequency	45Hz
Fuse Rating	25A

Related product manuals

Preview: PowerBass ASA SERIES

PowerBass ASA SERIES

Preview: PowerBass ASA 400.1x

PowerBass ASA 400.1x

PowerBass ASA 400.2x

Preview: PowerBass ASA 1000.1Dx

PowerBass ASA 1000.1Dx

PowerBass ASA 1500.1Dx

Preview: PowerBass ATM 330.2

PowerBass ATM 330.2

PowerBass ATM 550.4

Preview: PowerBass XAX 500D

PowerBass XAX 500D

Preview: PowerBass XTA 4000D

PowerBass XTA 4000D

Preview: PowerBass XTA 1000D

PowerBass XTA 1000D

Preview: PowerBass XAX 2160FD

PowerBass XAX 2160FD