Prevue Pet Products Silverado User Manual

L1
L3
L4
L2
A
B
L2
LEFT SIDE
FRONT
BACK
RIGHT SIDE
GRILLE
TRAY
SEED GUARD
U3
L3
U4
L4
A
C
B
U1
L1
U2
L2
T1 T2T2
{22} hex head screws
{ 8 } short hex head
screw & nut pairs for
seed guard
touch-up paint
& brush included
{ 1 } allen wrench
{ 4 } rolling casters
{ 3 } cup hangers
{ 3 } stainless steel cups
{ 1 } wood dowel perch
SG1
SG1
SG2SG2
KEY:
T = top
U = upper
L = lower
SG = seed guard
cage assembly instructions
Silverado Macaw Cage
Model: # 3155S
cage: 46"L × 36"W × 78¼"H
w/seed guard: 54¾"L × 44¾"W
interior: 45½"L × 35½"W × 63"H
wire: [gauge] 9 & 9 [spacing] 1⅜"
getting started!
READ THESE NOTES FIRST:
• Enlist A Friend: This is a large cage and requires two
people to assemble.
• Count Hardware: If any screws are missing, please
contact Prevue Customer Service.
• Review All Parts: If parts are bent during shipping,
pieces may be straightened with needle nose pliers. For seriously
damaged pieces, please contact Prevue Customer Service.
• Tools: An allen wrench is included. You may use your own
hand tool with an allen wrench bit. We
DO NOT recommend
power drills! Parts can be over-tightened and damaged/stripped.
Prevue is not responsible for this type of damage.
Review these instructions thoroughly before attempting to
assemble cage. If you still require assistance, please contact
Prevue Customer Service at 800.243.3624 or through links
online at prevuepet.com
parts
steps
1 Attach casters to legs of lower front (L1)
and lower back (L2) panels.
2
a
THIS STAGE REQUIRES TWO PEOPLE.
Attach left side lower (L3) panel to
front lower (L1) panel.
→
Channels on (L3) face toward interior of cage.
Install bottom and middle screw only.
Leave top screw out until STEPS 4a & b.
2
b
Attach right side lower (L4) panel to
front lower (L1) panel.
Attach back lower (L2) panel to sides,
continuing to attach with only bottom and
middle screws.
3 After lower cage has been assembled,
slide in the grille (A) and drawer (B).

Prevue Pet Products Silverado Specifications

General

Brand	Prevue Pet Products
Model	Silverado
Category	Pet Care Product
Language	English

Summary

Cage Assembly Instructions

Getting Started and Important Notes

Cage Parts Identification

Cage Assembly Steps

Attach Casters to Lower Panels

Attach casters to legs of lower front (L1) and lower back (L2) panels for stability.

Attach Left Side Lower Panel

Attach left side lower (L3) panel to front lower (L1) panel, facing channels inward.

Attach Right Side and Back Lower Panels

Attach right side lower (L4) and back lower (L2) panels to front panel using bottom/middle screws.

Install Grille and Drawer

Slide the grille (A) and drawer (B) into the assembled lower cage structure.

Attach Back Upper Panel

Attach back upper (U2) panel to back bottom (L2) panel, securing with screws.

Attach Front Upper Panel

Attach front upper (U1) panel to front bottom (L1) panel, aligning holes and securing.

Attach Side Upper Panels

Slide side upper panels (U3/U4) into channels on back/front upper panels, aligning wires.

Attach Top Roof Panels

Attach center top (T1) and side top (T2) roof panels, aligning hooks and wires.

Install Front Door

Slide female sleeves on the front door over the male posts.

Attach Seed Guards

Hook front/back seed guards (SG1) into sleeves and secure side guards (SG2) with screws.