1
priceindustries.com
|
PCM - INTERIOR AND PERIMETER ZONES COOLING AND HEATING - Manual
PCM - INTERIOR AND PERIMETER ZONES COOLING AND HEATING
PRODUCT OVERVIEW
PCM - INTERIOR AND PERIMETER ZONES COOLING AND HEATING
TABLE OF CONTENTS
Introduction
In this manual, you will find technical descriptions and
diagrams of underfloor system components along with
their installation instructions. Practical guidelines and
recommendations are also provided. If more information is
required about this equipment, please contact a Price sales
representative.
General Safety Guidelines
This document is intended for use by owner-authorized
operating/service personnel who are expected to possess the
required training to enable them to perform their tasks properly
and safely. This individual must have read and understood this
document and any referenced materials prior to performing any
task on this equipment. Also, it is essential that this individual
be familiar with and comply with all applicable governmental
standards and regulations pertaining to the task in question.
This individual must also verify that installation and connections
comply with local building codes. It is the obligation and
responsibility of the operating/service personnel to identify and
recognize these inherent hazards, protect themselves, and
proceed safely in completing their tasks. Failure to comply
with any of these requirements could result in severe personal
injury or death to themselves and people at the site, as well as
serious damage to the equipment and the property in which it
is situated.
The equipment discussed in this manual is relatively
complicated apparatus and must be handled with the
necessary precautions. Individuals may be exposed to certain
components or conditions such as refrigerants, oils, materials
under pressure, rotating components, and both high and low
voltage during installation, operation, maintenance or service
of this equipment. If misused or mishandled, each item has the
potential to cause bodily injury or death.
Safety Precautions
When using electrical appliances, basic safety precautions
should always be followed including the following:
1. Read all instructions.
2. Do not touch hot surfaces.
3. To protect against electrical shock do not immerse cord,
plugs, or Control Box in water or other liquids.
4. Unplug the unit when not in use and before cleaning.
5. Do not operate any appliance with a damaged cord or
plug or after the appliance malfunctions or has been
damaged in any manner. Return appliance to the nearest
authorized service facility for examination, repair or
adjustment.
6. The use of accessory attachments not recommended by
the appliance manufacturer may cause injuries.
7. Do not use outdoors.
8. Do not let cord hang over edge of a table or counter, or
touch hot surfaces.
9. Do not place on or near a hot gas or electric burner, or in a
heated oven.
10. Always attach plug to appliance first, then plug into the
power source. To disconnect, turn any control to “off”,
then remove plug from power source.
11. Do not use appliance for other than intended use.
12. Save these instructions.
Safety Symbols
The following symbols are used in this document to alert the
reader to areas of potential hazard:
CAUTION
Failure to observe may result in equipment damage.
WARNING
Failure to observe may result in personal injury, death or
equipment damage.
NOTE: Used to highlight additional information helpful to the reader.
Product Overview
Introduction ................................................................... 1
General Safety Guidelines..............................................1
Safety Precautions .......................................................1
Safety Symbols ............................................................. 1
Underfloor Systems Control Zones ................................ 2
General Description ....................................................... 3
Features of the PCM .....................................................4
Operation ...................................................................... 4
Installation & Mounting Instructions
Installation ..................................................................... 5
Price Flow Response Chart ........................................... 5
Input/Output Description ............................................... 6
Wiring ........................................................................... 7
Thermostat Installation .................................................. 8
How to use Thermostats ............................................... 9
Display Navigation
Initial Startup ............................................................... 10
Service Menu .............................................................. 11
Balancing Menu .......................................................... 12
VVT Menu ................................................................... 13
Setpoint Menu ............................................................. 14
Input Menu .................................................................. 15
Output Menu - Aux Binary ........................................... 16
Output Menu - Analog Outputs ................................... 17
Stat Setup Menu ......................................................... 18
Info Menu .................................................................... 19
Address Menu .............................................................20
Networking & Setup
BACnet Networking and Setup ................................... 21
Setting the Device Instance ......................................... 26
LINKER - USB Service Tool ......................................... 27
Maintenance
Troubleshooting ........................................................... 28
Hardware Specifications .............................................. 29
To Next Page
Loading...
