PART LIST--Model No. 831.299282 Ri299A"
To locate the
parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key Key Key
No. Qty. Description No. Qty. Description No. Qty. Description
1 1 Motor Belt 48 1 Shield 97 4 Thick Base Pad
2 1 Pulley/Flywheel/Fan 49 2 Belt Guide 98 1 12" Audio Wire
3 4 Motor Nut 50 1 Book Holder 99 1 Upright Grommet
4* 1 Motor/Pulley/ 61 1 Front Belly Pan 100 1 Allen Wrench
Flywheel/Fan 52 1 Power Supply 101 11 Screw
5 1 Incline Motor Bolt 53 4 Cable Tie Clamp 102 1 Lock Knob
6 1 Plastic Incline Motor 54 4 Cable Tie 103 2 Extension Leg
Spacer 55 1 Walking Belt 104 2 Extension Leg Cap
7 1 Incline Motor 56 1 20" Wire Harness 105 1 Shock
8 1 Stop Bracket 57 1 Rear Roller 106"* 2 Extension Leg
9 1 Small Nut 58 1 Belly Pan Spacer Assembly
10 2. Star Washer 59 2 Rear Foot 107 2 Pulse Bar Bolt
11 1 Optic Switch 60 1 Rear Foot Screw 108 2 Pulse Bar Washer
12 1 Frame 61 1 Ground Wire 109 1 Pulse Bar
13 1 Optic Switch Bolt 62 5 Ground Wire Screw 110 2 Handrail Foam Grip
14 1 Incline Optic Disk 63 1 Belly Pan 111 1 Lock Knob Sleeve
15 8 Incline Motor Nut 64 1 Rear Endcap 112 1 Spring
16 4 Hood Screw 65 2 Rear Roller Adj. Bolt 113 1 Lock Pin Collar
17 4 Plastic Stand-Off 66 1 Motor 114 1 Pin Clip
1B 2 Hood Bracket (short) 67 1 Latch Decal 115 1 Lock Pin
19 1 Hood Bracket (long) 68 4 Platform Screw 116 1 Console Base Bottom
20 2 Warning Decal 69 6 Electronics Screw 117 2 Upright Endcap
2-1 1 Reed Switch 70 1 Latch Catch 118"* 1 Chest Pulse Sensor
22 1 Reed Switch Clip 71 1 Walking Platform 119 8 Hood Bracket Screw/
23 1 Motor/Controller Wire 72 5 8" Cable Tie Incline Shield Screw
24 1 Controller 73 1 Jack 120 1 Rear Foot Spacer
25 1 Electronics Bracket 74 1 Motor Tension Bolt 121"* 1 Hand Weight Set
26 1 Circuit Breaker 75 2 Foot Rail Insert 122 1 Metal Incline Motor
27 1 Power Cord 76 18 Short Screw Spacer
28 1 Power Cord Grommet 77 1 Console 123 2 Static Decal
29 1 On/Off Switch 78 1 Choke 124 1 Hand Pulse Wire
30 1 Inlet Bracket 79 4 Long Screw 125 1 Choke Bracket
31 1 Incline Leg 80 1 10' I-Fit Wire 126 2 Base Pad
32 2 Frame Pivot Bolt 81 4 Motor Star Washer # 1 10" White Wire
33 2 Frame Pivot Spacer 82 1 Upright # 1 4" White Wire, M/F
34 1 Upright Wire Harness 83 2 Incline Leg Pivot Bolt # 1 8" Blue Wire, 2F
35 1 Front Roller Adj. Bolt 84 2 Incline Leg Pivot # 1 4" Blue Wire, 2F
36 3 Roller Adj. Washer Washer # 1 4" Black Wire, M/F
37 2 Motor Tension Nut/ 85 2 Handrail Extension # 1 4" Black Wire, 2F
Front Roller Nut 86 2 Wheel Bolt # 1 4" Green Wire, FIRing
38 4 Motor Bolt 87 1 Console Base # 1 8" Green Wire, F/Ring
39 2 Cap Screw 88 1 Motor Tension Washer # 1 8" Green Wire, 2 Ring
40 1 Left Foot Rail Cap 89 10 Console/Catch Screw # 1 4" Red Wire, M/F
41 2 Foot Rail 90 1 Key/Clip # 1 User's Manual
42 1 Front RolledPulley 91 1 Incline Motor Plate * Includes all parts shown in the
43 1 Magnet 92 1 Right Foot Rail Cap box
44 2 Platform Screw (re{d) 93 1 Motor Tension Spacer **For more information about the
45 2 Isolator 94 1 Motor Hood optional hand weight set or chest
46 4 Isolator Screw 95 2 Front Wheel pulse sensor, see page 18
47 15 Plastic Fastener 96 1 Incline Motor Shield # These parts are not illustrated
23
To Next Page
Loading...
