To Next PageTo Next PageWhat to do if Pro-Form endurance S7.5 PETL79715.0 power does not turn on?
First, ensure the power cord is properly plugged into an earthed outlet. If using an extension cord, it should be a 3-conductor, 14-gauge cord no longer than 5 ft. Also, make sure the key is inserted into the console. Finally, check the power switch on the treadmill frame; if it's tripped, wait five minutes, then press it back in to reset.
How to fix Pro-Form endurance S7.5 PETL79715.0 walking belt slipping?
To fix a slipping walking belt on your Pro-Form Treadmill, first remove the key and unplug the power cord. Then, using the hex key, turn both idler roller screws clockwise 1/4 of a turn. The belt should be tight enough that you can lift each edge 2 to 3 inches off the platform. Plug the treadmill back in, insert the key, and walk on it carefully for a few minutes. Repeat until the belt is properly tightened.
Why does my Pro-Form Treadmill power turn off during use?
If your Pro-Form Treadmill turns off during use, first check the power switch and reset it if it has tripped by waiting five minutes and then pressing the switch back in. Ensure the power cord is securely plugged in; try unplugging it, waiting five minutes, and plugging it back in. Also, remove and reinsert the key from the console.
How to center Pro-Form endurance S7.5 PETL79715.0 walking belt?
If the walking belt on your Pro-Form Treadmill isn't centered, first remove the key and unplug the power cord. If the belt has shifted left, turn the left idler roller screw clockwise 1/2 turn. If it has shifted right, turn the left idler roller screw counterclockwise 1/2 turn. Avoid overtightening. Plug the treadmill back in, insert the key, and run it.
What to do if Pro-Form endurance S7.5 PETL79715.0 walking belt slows down?
If the walking belt on your Pro-Form Treadmill slows down when you walk on it, make sure you are using the correct type of extension cord, if one is needed, use only a 3-conductor, 14-gauge (1 mm[2]) cord that is no longer than 5 ft. (1.5 m). If the walking belt is overtightened, remove the key and unplug the power cord. Using the hex key, turn both idler roller screws counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
How to recalibrate incline on Pro-Form endurance S7.5 PETL79715.0 Treadmill?
To recalibrate the incline on your Pro-Form Treadmill, hold down the Stop button and the Speed increase button, insert the key into the console, and then release the Stop button and the Speed increase button. Next, press the Stop button, and then press the Incline increase or decrease button. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. If the incline system does not begin calibrating, press the Stop button again, and then press the Incline increase or decrease button again.
Lists crucial safety rules like using handrails, safety clip, and avoiding moving parts.
Details on clothing, shoes, children/pets, weight limits, and speed adjustments.
Advises on stopping exercise if unwell and avoiding overexertion to prevent injury.
Explains how to connect the console assembly wires to the upright wires, warning about improper connection.
Emphasizes tightening all parts, removing protective plastic, and keeping the hex key safe.
Explains how to properly plug the power cord into the treadmill and an earthed outlet.
Highlights the importance of proper earthing and warns against modifying the plug or using damaged cords.
Provides a detailed diagram of the treadmill console, labeling all buttons and displays.
Reminds users to remove plastic, wear athletic shoes, and check belt alignment before first use.
Step-by-step guide to powering on the treadmill, including key insertion and safety clip usage.
Explains how to select manual mode and control speed and incline using console buttons.
Provides steps on how to safely fold the treadmill for storage, emphasizing incline zero and lifting capacity.
Details how to move the folded treadmill using its wheels, with safety precautions.
Step-by-step instructions for unfolding the treadmill from its storage position.
Guidelines for cleaning the treadmill exterior and walking belt safely.
Addresses problems like the power not turning on or turning off during use, including checking the switch and cord.
Explains how to adjust idler roller screws to fix a walking belt that slows down or is overtightened.
Provides steps to recalibrate the incline system if it does not change correctly.
Details how to adjust idler roller screws to keep the walking belt centered between the foot rails.
Instructions on tightening the walking belt using idler roller screws to prevent slipping.
General