ProForm CROSSWALK DUAL User Manual

5. SYMPTOM: THE CROSSWALK DOESNOT INCLINE
a. Standat the backof the footrailswhile increasingIhe incline.Stand at the front of the foot mils and lean for-
"ward while decreasingthe incline. (SeeOPERATION AND ADJUSTMENT.)
6. SYMPTOM:THEWALKING BELTSLOWSWHEN WALKEDON
a.
Siliconelubricant mustbe applied tothewalking platformbefore the CROSS WALK is used. Lubricantshouldbe
reapplied afterevery 10 hoursof use,and whenevera decreasein performance is noticed. (See OPERATION
AND ADJUSTMENT for applicationinstructions.)Uni0Sportsiliconespray isrecommended. CAUTION: ALWAYS
UNPLUGTHE POWER CORD WHEN APPLYINGLUBRICANT.
b.
C.
If an extensioncord is needed, useonly a 14-gauge general-purpose cord of five feet or less in length.
If thewalking belt is overtightened,performance may be reduced
and the walking belt permanently damaged. UNPLUGTHE POWER
CORD. Using the allen wrench included,turn bothrear roller
adjustmentboltscounterclockwise1/4 of a turn. When the tension
of the walking belt iscorrect, you shouldbe able to lifteach side of
the walking belt 2-3 inches;the center of thewalking beltshould
justtouchthesurfaceof thewalking platform.Besureto keep the
walking belt centered. Runthe treadmillfor a fewminutes.Repeat
untilthe tensionof the walking belt iscorrect. Note: Storethe allen
wrench in the handy wrench clip. Removethe backingfrom the
wrench clipand pressthe wrench cliponto one of the endcaps.
2"-3" RearRoller
AdjustmentBolts
Wrench CliI
7. SYMPTOM:THEWALKING BELTISOFF-CENTEROR SUPS
a.
b.
Ifthe walking belt hasshiftedto the left, firstUNPLUGTHE
POWER CORD. Using the allen wrench included,turn the leftrear
roller adjustmentboltclockwise, and the rightbolt counterclock-
wise 1/4 of a turneach. Runthe treadmillfor a few minutes.
Repeatas necessaryuntilthewalking beltiscentered.
ff the walking belt hasshiftedtothe right, first UNPLUGTHE
POWER CORD. Using the allen wrench included, turn the left rear
roller adjustment boll counterclockwise,and the right bolt clock-
wise 1/4 of a turn each. Run the treadmill for a few minutes.
Repeatas necessary untilthewalking belt is centered.
C_
If thewalking belt slipswhen walked on, first UNPLUGTHE
POWER CORD. Usingthe allenwrench included,turnboth rear
rolleradjustmentboltsclockwise 1/4 of alurn. When the tensionof
thewalking belt iscorrect,you shouldbe able to lifteach sideof
thewalking belt 2-3 inches;the center of thewalking belt should
just touchthe walking platform.Besuretokeepthe walking belt
centered. Runthetreadmillfora few minutes.Repeatas necessary
untilthe tensionof thewalking belt iscorrect.
a.
Beforeconvertingthe CROSSWALK tothe stowaway position,lurn the resistancecontrol(seethe drawing on page
7) counterclockwiseuntil the canlrol turns freely.Next, unplugIhe power cord. RemoveIhe lockknob and washer
fromIheupright and lay the uprightand Ihe upper body armson the walking belt. Keepthe lock knoband washer in a
securelocation.
.g

ProForm CROSSWALK DUAL Specifications

General

Brand	ProForm
Model	CROSSWALK DUAL
Category	Treadmill
Language	English