Quick installation Guide http://www.prostart.org P.7
x to shut down the engine without affecting the doors.
7. The parking lights will flash twice to confirm ready mode activation.
The system will exit ready mode if a door, the hood or the trunk is opened, if the brake pedal is pres-
sed, if the parking brake is disengaged or if the ignition key is turned to the IGNITION ON (RUN)
position.
Remote-start the engine and listen for starter drag. If the starter cranks for too long, carry out
another tach programming procedure.
Hood switch shutdown. With the vehicle running remotely, open the hood; the vehicle should shut
down. If it does not shut down, check the hood pin-switch and its connector.
Brake shutdown circuit. With the vehicle running remotely, press and release the brake pedal. The
engine should shut down immediately. If it continues to run, check the brake switch connection.
Parking brake shutdown circuit (manual transmissions only). With the vehicle running under
remote start, disengage the parking brake. The engine should shut down immediately. If the engine
continues to run, check the parking brake switch connection.
OEM alarm control. Make sure the module is able to arm and disarm the OEM alarm (if applicable).
Door locks and trunk testing. Make sure each of these options respond to the transmitter (if
installed).
Door pin shutdown circuit (manual transmissions only). Make sure the system exits ready mode
when each door is opened. (Test each door.)
Starter kill option. Sit inside the vehicle with all doors closed. Arm the vehicle, then try to start the
engine with the key. The engine should not start. If the engine starts, rewire the starter kill to reach
proper operation.
Valet mode. Make sure the remote car starter is able to properly enter and exit valet mode. When
setting the remote car starter into valet mode, pressing the lock button will lock the doors without
activating the starter kill. (Refer to the user guide for further information on valet mode.)
Idle mode. Make sure the vehicle properly enters and exits idle mode.
Door trigger. Make sure that when the system is armed, opening any door or opening the trunk will
trigger the alarm (if installed).
Hood trigger. Make sure that when the system is armed, opening the hood should trigger the alarm.
Most comebacks are the result of misunderstandings about how a product works or performs.
Take the time to properly explain all functions and features to the customers before they leave
the premises. Doing this will save time and money.
P.4 http://www.prostart.org Quick Installation Guide
OPTION 1 Ignition Valet DISABLED
OPTION 2* Ignition Valet ENABLED
MODE 3
* INDICATES DEFAULT SETTING
FUNCTION 1 – Home Valet
OPTION 1 Home valet ENABLED
OPTION 2* Home valet DISABLED
FUNCTION 2 – AUX 1 Programming
OPTION 1 Horn confirmation upon the 2
nd
press of the LOCK button
OPTION 2* Priority door access
OPTION 3 Horn confirmation upon the 1
st
press of the LOCK button
FUNCTION 3 – AUX 2 Programming
OPTION 1 Constant output
OPTION 2* Toggle ON/OFF (with 30-second time out)
OPTION 3 4-minute ON/OFF toggle (only when running under remote start)
OPTION 4 Priority door access
FUNCTION 4 – AUX 3 / Trunk output
OPTION 1 1-sec. output when the TRUNK button is pressed for 3 sec. with ignition OFF or when
started remotely with data output
OPTION 2* Constant output while the TRUNK button is pressed.
OPTION 3 Trunk & Data output with disarm and rearm pulses
FUNCTION 5 – External Trigger
OPTION 1 Zone 3 with disarm/rearm (trunk monitor)
OPTION 2* Key sense
OPTION 3 Engine start/stop
OPTION 4 SmartStart™
MODE 4
* INDICATES DEFAULT SETTING
FUNCTION 1 – Multi-level features
OPTION 1 Multi-car features, Basic features, Customized features
OPTION 2* Basic features, Multi-car features, Customized features
OPTION 3 Customized features, Multi-car features, Basic features
OPTION 4 Basic features, Customized features, Multi-car features
FUNCTION 2 – Alarm control
OPTION 1 ENABLED (HORN must be enabled in MODE 3 FUNCTION 2, Option 1 or 3)
OPTION 2* DISABLED
FUNCTION 3 – Ready Mode Option
OPTION 1 ENABLED by handbrake
OPTION 2* ENABLED by remote
FUNCTION 4 – Bypass
OPTION 1 ADS (1W D2D)
OPTION 2* Xpresskit (2W D2D)
OPTION 3 Fortin (1W D2D)
FUNCTION 5 – Bypass Type
OPTION 1 One-Way communication
OPTION 2* Two-Way communication (For Xpresskit only)
To Next Page
Loading...
