Prusa Research Original Prusa XL User Manual (English)

To Next Page

Table of Contents

1. Introduction 5 ......................................................................................................................

Step 1 - Preparing the upgrade kit 6 ..............................................................................

Step 2 - Getting the necessary tools 6 ...........................................................................

Step 3 - Getting the necessary tools 7 ...........................................................................

Step 4 - Labels guide 7 .....................................................................................................

Step 5 - Cheatsheet 8 .......................................................................................................

Step 6 - Front, left, right and rear side 8 .......................................................................

Step 7 - Manipulating with the printer 9 .......................................................................

Step 8 - Spare nozzles 9 ...................................................................................................

Step 9 - Silicone sock 10 ..................................................................................................

Step 10 - View high resolution images 10 .....................................................................

Step 11 - We are here for you! 11 ......................................................................................

Step 12 - How to successfully finish the assembly 12 .................................................

Step 13 - Reward yourself 13 ............................................................................................

Step 14 - Prepare your desk 13 ........................................................................................

2. Printer preparing 14 ..........................................................................................................

Step 1 - Preparing the printer 15 ......................................................................................

Step 2 - Protecting the heatbed 15 .................................................................................

Step 3 - Printer unpluging 16 ...........................................................................................

Step 4 - Can I open the Haribo? 16 .................................................................................

Step 5 - Let's get started 17 ..............................................................................................

3. Detaching the Nextruder 18 ...........................................................................................

Step 1 - Tools necessary for this chapter 19 ..................................................................

Step 2 - Wi-Fi antenna detaching 19 ..............................................................................

Step 3 - PTFE unpluging 20 ............................................................................................

Step 4 - Disconnecting the Nextruder cable 20 ...........................................................

Step 5 - Detaching the dock 21 .......................................................................................

Step 6 - Detaching the Nextruder 21 ..............................................................................

Step 7 - Detaching the Nextruder 22 .............................................................................

Step 8 - Still no sweets? 22 .............................................................................................

Step 9 - Good job! 23 ........................................................................................................

4. ToolChanger assembly 24 ..............................................................................................

Step 1 - Tools necessary for this chapter 25 .................................................................

Step 2 - Preparing the X-carriage 25 .............................................................................

Step 3 - Installing the ToolChanger: parts preparation 26 ........................................

Step 4 - Preparing the ToolChanger 26 .........................................................................

Step 5 - Installing the ToolChanger 27 ..........................................................................

Step 6 - Covering the X-carriage 27 ...............................................................................

Step 7 - Haribo 28 ..............................................................................................................

Step 8 - Almost done 28 ...................................................................................................

5. Nextruder upgrade 29 ......................................................................................................

Step 1 - Tools necessary for this chapter 30 .................................................................

Step 2 - Dock disassembly: parts preparation 30 ........................................................

Step 3 - Dock disassembly: cable bundle 31 .................................................................

Step 4 - Dock disassembly 31 ..........................................................................................

Step 5 - New dock assembly: parts preparation 32 .....................................................

Step 6 - New dock assembly: inserting the nut 32 ......................................................

Step 7 - New dock assembly: metal dock 33 ................................................................

Step 8 - New dock assembly: upper screw 33 .............................................................

Filament diameter	1.75 mm
Nozzle Temperature	Up to 300 °C
Heated Bed Temperature	Up to 120 °C
Power Panic	Yes
Extruder Type	Direct drive
Build volume	360 x 360 x 360 mm
Nozzle diameter	0.4 mm (default)
Connectivity	USB, Ethernet, Wi-Fi
Supported materials	PLA, PETG, ASA, ABS, PC, HIPS, PVA, PVB
Automatic First Layer Calibration	Yes
Tool Changer	Up to 5 independent tool heads
Bed Leveling	Automatic
Power Consumption	Max 500 W
Power Input	110-240 V AC, 50/60 Hz

Prusa Research Original Prusa XL User Manual

Table of Contents

Other manuals for Prusa Research Original Prusa XL

Prusa Research Original Prusa XL Specifications

Related product manuals