EasyManuals Logo

Q Acoustics M2 User Manual

Q Acoustics M2
24 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #7 background imageLoading...
Page #7 background image
7
IPA
– Q Acoustic’s Intelligent Pre-Amplifier removes the need for a remote control through a
signal sensing matrix to enable auto source selection and auto on/off.
MoviEQ
– Q Acoustic’s Movie EQ helps to maximise the drama and excitement of a movie or
TV soundtrack. Toggle it on or off for music and movie settings.
NFC – Near Field Connection allows simple connection of Bluetooth
®
devices by tapping the
NFC location on the Q Acoustics speaker.
HDMI ARC – High Definition Multimedia Interface Audio Return Channel removes the need for
additional Optical or Analogue audio cables between source and speaker.
CEC – Consumer Electronics Control syncronises TV remote control of Volume, Mute and
Standby for easy integration of our Q Acoustics speaker.
Bluetooth
®
– An international wireless connection used for streaming audio from all compatible
devices.
aptX
– A high definition audio CODEC used for Bluetooth
®
streaming.
AVRCP – A Bluetooth control protocol that synchronises your device control of Volume and
Mute for easy integration of our Q Acoustics speaker.
DAC – Digital to Analogue Converter which determines the bit depth and sample rate of the Q
Acoustics speaker; the higher the number, the better the audio quality.
BMR – Balanced Mode Radiators are Q Acoustics mid/high driver of choice, they have a flat
radiating surface which enables their dispersion to fill a room with sound.
DVC – Dual Voice Coil subwoofers are Q Acoustics subwoofer driver of choice, it has two voice
coils in one driver for greater flexibility of design and improved bass control.
Sub Out – A Phono subwoofer output for connection to an external subwoofer. On some of
our older products the additional sub out provides a huge bottom end when used with a Q
Acoustics subwoofer.
Dynamic Bass – Improved response, loudness, depth and control of bass frequencies is
achieved through our dynamic bass enhancement system, to perfectly integrate our inbuilt
DVC subwoofer.
User EQ – User control of EQ setting for best acoustic performance. This can be changed
dependent upon speaker position, mounting, or user preference.
LSG
–Q Acoustic’s Low Source Gain switch increases the incoming signal level to get
maximum performance from your system when connected to low output signal equipment via
HDMI or Optical.
Power Rating – Total continuous power rating of the system in Watts. Eg. BT3 = 2 x 50W =
100W.
Lip Sync – Adjustable delay for lip synchronisation between TV/screen and Q Acoustics
speaker.
3.5mm – 3.5mm jack socket for Analogue input.
RCA – Stereo phono socket for Analogue input.
Feature summary

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Q Acoustics M2 and is the answer not in the manual?

Q Acoustics M2 Specifications

General IconGeneral
EqualizerYes
RMS rated power80 W
Audio output channels- channels
Number of speakers2
Crossover frequency340 Hz
Signal-to-Noise Ratio (SNR)-85 dB
Total Harmonic Distortion (THD)0.9 %
Subwoofer locationBuilt-in
Product colorBlack
Wall mountable-
Audio formats supportedMP3, SBC, apt-X
Bluetooth version4.0
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Soundbar power consumption100 W
Power consumption (standby)0.5 W
Power consumption (typical)11 W
Package depth428 mm
Package width615 mm
Package height178 mm
Package weight7900 g
Cables includedAC, HDMI
Number of products included1 pc(s)
Weight and Dimensions IconWeight and Dimensions
Depth338 mm
Width550 mm
Height93 mm
Soundbar weight5800 g

Related product manuals