EasyManuals Logo
Home>QNAP>Network Hardware>TS-431P

QNAP TS-431P User Manual

QNAP TS-431P
135 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #5 background imageLoading...
Page #5 background image
5
FCC Class B Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Modifications: Any modifications made to this device that are not approved by QNAP
Systems, Inc. may void the authority granted to the user by the FCC to operate this
equipment.
CE NOTICE
QNAP NAS comply with different CE compliance classes. Please refer to the Appendix for
details.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the QNAP TS-431P and is the answer not in the manual?

QNAP TS-431P Specifications

General IconGeneral
Processor cores2
Processor modelAL212
Processor familyAnnapurna Labs
Processor frequency1.7 GHz
Flash memory512 MB
Internal memory1 GB
Internal memory typeDDR3
RAID levels0, 1, 5, 6, 10, JBOD
RAID supportYes
Storage drive size- \
Storage drive capacity0 GB
Supported file systemsFAT32, HFS+, NTFS, ext3, ext4
Storage drive interface-
Storage drives installedNo
Storage drive sizes supported2.5, 3.5 \
Supported storage drive typesHDD & SSD
Total installed storage capacity0 TB
Number of storage drives installed0
Number of storage drives supported4
Supported storage drive interfacesSerial ATA, Serial ATA II, Serial ATA III
Ethernet LAN data rates10, 100, 1000 Mbit/s
Supported network protocolsIPv4, IPv6, CIFS/SMB, AFP (v3.3), NFS(v3), FTP, FTPS, SFTP, TFTP, HTTP(S), Telnet, SSH, iSCSI, SNMP, SMTP, SMSC
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity3
Chassis typeTower
Cooling typeActive
Fan diameter120 mm
Product colorWhite
LED indicatorsHDD, LAN, Status, USB
Number of fans1 fan(s)
Cable lock slot typeKensington
TypeNAS
Noise level19.5 dB
Device classHome & Home Office
Share folderCIFS/SMB
Backup featuresCloud, iSCSI LUN
Browser supportedInternet Explorer 10+, Firefox 8+, Safari 4+, Chrome
Security algorithms256-bit AES, HTTPS, SNMP, SSH, SSL/TLS
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)5 - 95 %
Fan voltage12 V
AC input voltage100-240 V
Power supply locationExternal
Power consumption (typical)26.7 W
Number of power supply units1
Power supply unit (PSU) capacity90 W
Cables includedAC, LAN (RJ-45)
Operating system version4.2
Operating system installedQNAP Turbo System
Server operating systems supportedWindows Server 2003, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2
Windows operating systems supportedWindows 10 Education, Windows 10 Education x64, Windows 10 Enterprise, Windows 10 Enterprise x64, Windows 10 Home, Windows 10 Home x64, Windows 10 Pro, Windows 10 Pro x64, Windows 7 Enterprise, Windows 7 Enterprise x64, Windows 7 Home Basic, Windows 7 Home Basic x64, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional, Windows 7 Professional x64, Windows 7 Starter, Windows 7 Starter x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows 8, Windows 8 Enterprise, Windows 8 Enterprise x64, Windows 8 Pro, Windows 8 Pro x64, Windows 8 x64
Weight and Dimensions IconWeight and Dimensions
Depth169 mm
Width160 mm
Height219 mm
Weight3000 g
Package weight4300 g

Related product manuals