QOLSYS IQ MOTION-S User Manual

IQ MOTION S-LINE INSTALLATION MANUAL
•
Advanced circuit technology
resulting in ultra-low power
consumption
•
40 lb. Pet immunity
•
Tamper detection/reporting
•
Rigid wall mounting for discreet
placement
•
Easy to install batteries
•
Supervisory health messaging
PRODUCT FEATURES
IQ MOTION-S
•
Wireless signal range: 600 ft, open air
•
Compatible control panels: Qolsys IQ Panel 2
•
Code outputs: paring, tamper, tamper restore, alarm detect motion,
alarm restore, supervisory, low battery
•
Transmitter frequency: 319.5MHZ +-15KHz
•
Transmitter bandwidth: 24KHZ
•
Modulation type: ASK-OOK
•
RF output power!91.1dBuV +/- 5% at 3m
•
Sensor Range 30 ft x 40 ft
•
Maximum Horizontal Sensing Angle 80°
•
Sensor: 3.4H x 2.4W x 1.5D in.
•
Replace batteries every 5 years with AAA Alkaline (x2). Detector
intended for use with (2) Huizhou Deanda Battery Co. AAA LR03.
TECHNICAL SPECIFICATIONS
•
The sensor should be permanently mounted in a corner or on a
flat wall that is free of vibrations, at a height of 7.5 feet.
•
Mount the sensor on an insulated exterior wall facing in.
•
Position the sensor to protect an area where an intruder is most
likely to walk across the detection pattern.
•
Position the sensor so it faces a solid reference point, such as a
wall.
•
If possible, mount the sensor within 100 ft of the panel. While
the transmitter may have a range of 600 ft or more out in the
open, the environment at the installation site can have a
significant effect on transmitter range. Verify actual transmitter
range for each installation.
•
Close all windows in an area with an armed motion sensor.
STEP
1
CHOOSE
INSTALLATION
LOCATION
•
Aim the sensor at windows, fireplaces,
air conditioners, area heaters, forced
air heating vents or drapes.
•
Place the sensor in direct sunlight as
sudden changes in temperature may
trigger a false alarm.
•
Mount the sensor near duct work or
other large metallic surfaces that may
affect the RF signals.
•
Set the sensor on a shelf.
•
Mount outdoors or in a non-
temperature controlled environment.
•
Mount at any other height than 7.5 ft.
Qolsys Inc. proprietary. Reproduction without permission is not permitted.
LOCATION MOUNTING GUIDELINES:
DO NOT:
X
Avoid placement
looking at ceiling
fans
✓
Outside walls
pointed away from
windows are great
locations
X
Avoid
HVAC
ducts &
drapes
X
✓
Must
install at
7.5’ high
✓
Position so that the expected motion is perpendicular to
the zones of detection. Test yearly.
Note: For UL/CUL installations use this device only in conjunction
with compatible Qolsys wireless alarm system IQ Panel 2.

QOLSYS IQ MOTION-S Specifications

General

Type	Motion Sensor
Field of View	90 degrees
Battery	CR123A
Battery Life	Up to 5 years
Pet Immunity	Up to 40 lbs
Sensor Type	Passive Infrared (PIR)
Power Source	3V Lithium Battery
Compatibility	QOLSYS IQ Panel
Operating Temperature	32°F to 120°F
Detection Range	Up to 40 feet

Summary

Product Features and Specifications

Product Features

Highlights advanced circuit technology, pet immunity, tamper detection, rigid wall mounting, and supervisory messaging.

Technical Specifications

Details wireless range, compatible panels, code outputs, frequency, bandwidth, RF output power, and sensor dimensions.

Installation Location and Guidelines

Mounting Guidelines

Recommends mounting at 7.5 feet, on an insulated wall, facing a solid reference point, and within 100 ft of the panel.

Prohibited Placement

Advises against aiming at windows, fireplaces, HVAC vents, direct sunlight, or near metallic surfaces.

Modes and Behaviors

Normal Mode

Defines the standard operating state with limited active event transmissions and a 5-minute sleep timer after first event.

Sleep Mode

A limited period where the detector conserves battery by not transmitting active or idle events.

Walk Test Mode

Activates the detector's LED to indicate motion detection for coverage testing.

Pet Immunity

Details the detector's immunity to pets up to 40 lbs when mounted correctly.

Detection Pattern and Maintenance

Detection Pattern

Illustrates the top and side views of the sensor's detection range and angles.

Battery Replacement

Provides instructions for replacing the two AAA alkaline batteries.

Environmental Specifications

Lists operating and storage temperature ranges and maximum relative humidity.