Why is the image too dark or light on my Raymarine Marine GPS System?
If the image on your Raymarine Marine GPS System is too dark or too light, adjust the brightness controls at the display accordingly. You can also use the appropriate menu in the thermal camera application to adjust the contrast and brightness of the image. Finally, use the SCENE button to select a scene mode appropriate for the current conditions.
Why does my Raymarine Monitor not turn on or keep turning off?
Your Raymarine Monitor might not be turning on or keeps turning off due to several reasons: a blown fuse or tripped breaker (check and replace if necessary, and inspect for cable damage if fuses repeatedly blow), a poor or damaged power supply cable or connections (ensure the cable is fully inserted and locked, check for damage or corrosion, and flex the cable to check for reboots), incorrect power connection (ensure the installation instructions have been followed), or an insufficient power source (check the power supply voltage under load).
What to do if my Raymarine Monitor displays a “No Fix” GPS status icon?
If your Raymarine Monitor displays a 'No Fix' GPS status icon, it could be due to your geographic location or prevailing conditions preventing a satellite fix (check periodically in better conditions or another location), a GPS connection fault (ensure external GPS connections and cabling are correct), or an external GPS antenna in a poor position (ensure the GPS antenna has a clear view of the sky).
What to do if my Raymarine Monitor will not boot up (re-boot loop)?
If your Raymarine Monitor will not boot up, it could be due to the power supply and connection issues. Also, in the unlikely event that the product's software has become corrupted, please try re-flashing the latest software from the Raymarine website. On display products, as a last resort, you can try to perform a ‘Power on Reset’; however, this will delete all settings/presets and user data and revert the unit back to factory defaults.
What does it mean if my Raymarine Monitor displays 'No Data' or 'No scanner message'?
If your Raymarine Monitor displays 'No Data' or 'No scanner message', check the scanner power supply cable to ensure it's sound and connections are tight and free from corrosion. Also, check that the scanner is correctly connected to a Raymarine network switch or SeaTalkhs crossover coupler, as applicable. Ensure the scanner pedestal switch is in the ON position.
Why can't I switch between thermal and visible video on my Raymarine Marine GPS System?
If you cannot switch between thermal and visible (VIS / IR) video image on your Raymarine Marine GPS System, it may be because the camera is not a dual payload model. Only dual payload (dual lens) thermal cameras support VIS / IR switching. Also, ensure that the VIS / IR cable is connected from the camera to the Raymarine system.
Why are the controls on my Raymarine Marine GPS System erratic?
If the controls on your Raymarine Marine GPS System are erratic or unresponsive, check that the controller and thermal camera are correctly connected to the network. Ensure that no other controllers are in use at the same time. Check the power/network cabling to the controller and PoE injector.
Why is my Raymarine Marine GPS System showing an incorrect speed reading?
If you're getting an incorrect speed reading on your Raymarine Marine GPS System, check that the paddle wheel is clean. Add a speed offset if none is set. Re-calibrate the equipment if necessary.
Why is the radar bearing incorrect on my Raymarine Marine GPS System?
If the bearing of a target on the radar screen of your Raymarine Marine GPS System is incorrect, the radar bearing alignment requires correcting. Check and adjust the radar bearing alignment.
Why is video not displayed on my Raymarine Marine GPS System?
If the video is not displayed on your Raymarine Marine GPS System, it could be because the camera is in Standby mode. Use the camera controls (either the thermal camera application or JCU) to wake the camera from standby. Also, check the thermal camera video cables to ensure they are properly connected. Finally, verify the power connections to the camera and JCU / PoE injector (if used).
General| GPS | Yes |
|---|---|
| Chartplotter | Yes |
| Radar Compatible | Yes |
| Sonar | Yes |
| Display Type | Color LCD |
| Chart Compatibility | Navionics |
To Next Page