What to do if my Raymarine Transceiver shows no GPS position information?
If your Raymarine Transceiver shows no GPS position information or the graph displays only blue bars, verify the GPS antenna connections and power cycle the AIS unit. Also, ensure the GPS antenna has a clear view of the sky and is suitable for use with AIS, referring to the AIS installation manual for its specifications.
Why does my Raymarine AIS500 show a VHF Antenna VSWR fault?
If your Raymarine Transceiver displays the 'VHF Antenna VSWR fault' alarm, check the VHF antenna connections and consult the AIS installation manual to ensure the antenna is suitable for use with the AIS.
What to do if my Raymarine AIS500 displays an active alarm for position sensor, SOG, or COG data fault?
If your Raymarine Transceiver shows an active alarm for Position sensor fault, SOG data fault, or COG data fault, allow at least five minutes for the unit to acquire a GPS position fix. Refer to the troubleshooting guide for the GPS tab for further assistance.
How to fix Raymarine AIS500 Transceiver when no AIS is detected?
If your Raymarine Transceiver does not detect AIS, verify that the AIS is connected to the correct serial port in the settings menu. Ensure the AIS is powered on. If the issue persists, try using a different serial cable.
What does the 'Channel A Noise fault' or 'Channel B Noise fault' alarm mean on my Raymarine AIS500?
If your Raymarine Transceiver displays an active alarm indicating a Channel A or Channel B Noise fault, check the VHF antenna connections and consult the AIS installation manual to ensure the antenna meets the specifications. Note that this alarm may temporarily appear in busy shipping channels, which is normal for Class B AIS.
What to do if my Raymarine AIS500 cannot communicate with the unit?
If your Raymarine Transceiver cannot communicate with the unit, check that the AIS is connected to the correct serial port selected in the drop-down menu. If the problem persists, try using a different serial cable.
How to correct incorrect static data on my Raymarine Transceiver?
If the static data on your Raymarine Transceiver is incorrect, re-enter the static data and save it to the AIS. Note that the MMSI cannot be updated.
What to do if my Raymarine AIS500 Transceiver shows an active alarm with a message not listed?
If your Raymarine Transceiver displays an active alarm with a message not listed, check the VHF antenna connections and consult the AIS installation manual to ensure the antenna is suitable for use with the AIS. Please contact your dealer.
How to display static data on Raymarine AIS500 Transceiver?
If no static data is displayed on your Raymarine Transceiver, configure the unit by following the instructions in the Static data section.
Why the MMSI can not be changed on my Raymarine Transceiver?
The MMSI can only be programmed once on the Raymarine Transceiver. If it is incorrect, please contact your dealer.
Details how to launch the proAIS application and establish a serial connection to the AIS500 Transceiver.
Configuring vessel static data in the AIS Transceiver.
Guides on completing data fields for vessel configuration and saving to the AIS.
Warns about the immutability of the MMSI number once programmed and the need for accuracy.
Details status checks like MMSI validity, GPS fix, and position report transmission/reception.
Explains actions needed when red crosses appear next to status items like MMSI or GPS fix.
Lists active alarm messages generated by the AIS unit and how they clear.
Guides on selecting an update file, starting the update, and following on-screen instructions.
Warns against interrupting power or disconnecting during the update process.
Troubleshooting detection and communication failures with the AIS unit.
Resolving issues with vessel data configuration, MMSI, or incorrect static data.
Addressing problems related to GPS fix acquisition and antenna connection.
General| AIS Class | Class B |
|---|---|
| Transmit Power | 2W |
| NMEA Interface | NMEA 0183 |
| NMEA 2000 Compatible | Yes |
| Waterproof Rating | IPX6 |
| SeaTalkng | Yes |
| Frequency | 161.975 MHz and 162.025 MHz |
| Operating Temperature | -15°C to +55°C |
| GPS Receiver | Internal 50-channel GPS |
To Next Page
