To Next PageTo Next Page
Need help?Do you have a question about the RedMax RZT48x and is the answer not in the manual?
General| Fuel Capacity | 3.5 gallons |
|---|---|
| Cutting Width | 48 inches |
| Cutting Height | 1.5 - 4.5 inches |
| Transmission | Hydrostatic |
| Deck Material | Steel |
| Warranty | 3 years |
Basic information about the machine and manual.
Regulations and safety for road use.
Precautions and guidelines for towing equipment.
How to use the machine safely and correctly.
Importance of authorized service and support.
Location and details of machine identification numbers.
Highlights crucial details to prevent damage or misuse.
Essential guidelines to prevent injury or death.
Measures to ensure child safety around the machine.
Basic operational safety rules.
Safe practices for operating on inclines.
Recommended protective gear for safe operation.
Precautions for storing and using gasoline.
Guidelines for safely moving the machine.
Specific instructions and warnings for towing.
Information on the spark arrestor requirement.
Safety features and usage of the ROPS.
How to operate the steering and control movement.
Adjusting engine speed and blade rotation.
Starting and stopping the engine.
Function for cold engine starts.
Engaging and disengaging the mower deck.
Tracks operating hours and maintenance needs.
How to adjust the operator's seat for comfort.
Location and function of the fuel shut-off valve.
Location and purpose of the machine's fuses.
Adjusting the mower deck cutting height.
How to adjust the mower for straight operation.
Mechanism for manual movement of the machine.
Capacity, safety, and type of fuel to use.
Essential steps before operating the machine.
How the zero-turn steering system works.
Pre-operation checks and preparations.
Step-by-step guide to starting the engine.
Procedures for operating the machine in motion.
How to safely shut down the engine.
Engaging bypass linkages for manual movement.
Safe operation procedures on slopes.
Advice for optimal cutting results.
How the machine's safety interlocks function.
Operation and checks for the parking brake.
Recommended tire inflation levels.
Inspection and replacement of drive belts.
Steps to remove the mower deck drive belt.
Steps to install the mower deck drive belt.
Care, charging, and replacement of the machine's battery.
How to clean battery components to ensure good connection.
Procedure for installing a new battery.
Information on drive belts for the pump system.
Steps to replace the pump drive belt.
Importance of sharp, undamaged blades.
How to remove and install mower blades.
Procedures for leveling and adjusting the deck.
Maintenance specific to the transmission system.
Inspection and replacement of front caster wheels.
Adjustment of rollers to prevent deck scalping.
General cleaning procedures for the machine.
Checking for loose or missing fasteners.
Recommended lubrication intervals and types.
How to check and change the engine oil.
Lubricating wheel mounts and deck spindles.
Lubrication points for front wheel assemblies.
Lubrication points for front wheel bearings.
Lubrication points for mower deck spindles.
Steps for changing transmission fluid.
Procedures to remove air from the hydrostatic system.
Steps to diagnose engine starting issues.
Troubleshooting starter motor problems.
Diagnosing causes of engine misfires or poor running.
Identifying issues causing loss of power.
Causes and solutions for engine overheating.
Troubleshooting battery charging system failures.
Diagnosing drive system issues.
Resolving problems with blade engagement.
Identifying and fixing transmission fluid leaks.
Causes and remedies for poor cut quality.
Diagnosing and fixing excessive machine vibration.
Preparing the machine for long-term storage.
Recommended torque values for fasteners.
Torque values for standard US fasteners.
Torque values for standard metric fasteners.
Actions performed upon machine delivery.
Maintenance tasks after initial 10 hours of operation.
Routine checks and maintenance performed daily.
Maintenance tasks required every 25 hours.
Maintenance tasks required every 50 hours.
Maintenance tasks required every 100 hours.
Maintenance tasks required every 300 hours.
Annual maintenance tasks.
