Renesas e1 User Manual

E1/E20/E2/E2 Lite Additional Document Contents
R20UT2937EJ0301 Rev.3.01 Page 4 of 45
Jul 1, 2020
Contents
Page
1. Overview ........................................................................................................................... 7
1.1 Overview of E1/E20/E2 Emulator and E2 emulator Lite ............................................................................ 7
1.2 Note on Using E20 ..................................................................................................................................... 7
1.3 Configuration of Manuals ........................................................................................................................... 8
1.4 Supported Devices ................................................................................................................................... 10
1.5 Overview of the Specifications of the External Trigger Input and Output ................................................ 11
1.5.1 Assignments of the External Trigger Input and Output Pins .......................................................... 11
1.5.2 Specifications of the External Trigger Inputs and Outputs ............................................................. 12
2. Designing the User System .............................................................................................13
2.1 Connecting the E1/E20/E2/E2 Lite to the User System .......................................................................... 13
2.2 Installing the Connector on the User System .......................................................................................... 13
2.2.1 Connecting the User System Interface Cable to the 14-Pin Connector......................................... 13
2.3 Pin Assignments of the Connector on the User System .......................................................................... 17
2.3.1 14-Pin Connector Specifications .................................................................................................... 17
2.4 Recommended Circuits between the Connector and the MCU ............................................................... 19
2.4.1 Connection between the 14-Pin Connector and the RL78 Family MCUs ...................................... 19
2.5 Notes on Connection ............................................................................................................................... 20
2.5.1 RESET# Pin ................................................................................................................................... 21
2.5.2 TOOL0 Pin ..................................................................................................................................... 22
2.5.3 GND ............................................................................................................................................... 23
2.5.4 VDD ................................................................................................................................................ 23
2.6 Internal Circuits of the Emulator .............................................................................................................. 25
2.6.1 Internal Circuits of the E1 (when the RL78 Family is Connected) ................................................. 25
2.6.2 Internal Circuits of the E20 (when the RL78 Family is Connected) ............................................... 26
2.6.3 Internal Circuits of the E2 (when the RL78 Family is Connected) ................................................. 27
2.6.4 Internal Circuits of the E2 Lite (when the RL78 Family is Connected) .......................................... 28
2.7 Notes on Designing the User System ...................................................................................................... 29
2.7.1 Isolator for the E1 ........................................................................................................................... 29
2.7.2 Low-Voltage OCD Board ................................................................................................................ 29
2.7.3 Small Connector Conversion Adapter for the E1 ........................................................................... 30
3. Notes on Usage ...............................................................................................................32
3.1 Turning the Power On/Off ........................................................................................................................ 32
3.1.1 When a Separate Power Supply is Used for the User System ...................................................... 32
3.1.2 When Power is Supplied to the User System from the Emulator (E1/E2/E2 Lite Only) ................ 34
3.2 Power Supply Function of the E1/E2/E2 Lite ........................................................................................... 35
3.3 MCU Resources to be Occupied ............................................................................................................. 36
3.3.1 Securing an Area for the Debugging Monitor Program .................................................................. 36
3.3.2 Securing a Stack Area for Debugging ............................................................................................ 37
3.3.3 Setting an On-Chip Debugging Option Byte .................................................................................. 37
3.3.4 Setting a Security ID ...................................................................................................................... 38
3.3.5 Area for Pseudo-RRM/Pseudo-DMM ............................................................................................. 38
3.4 Reset ........................................................................................................................................................ 39
3.4.1 Operation after a Reset .................................................................................................................. 39
3.4.2 SP Value after a Reset ................................................................................................................... 39
3.5 Flash Memory .......................................................................................................................................... 39
3.5.1 Operation for Voltages Not Permitting Flash Memory Rewriting ................................................... 39
3.5.2 Notes on Flash Memory Rewriting ................................................................................................. 39
3.6 RESET# Multiplexed Pin.......................................................................................................................... 39
3.7 MCUs that are Used in Debugging .......................................................................................................... 40

Renesas e1 Specifications

General

Brand	Renesas
Model	e1
Category	Computer Hardware
Language	English