1
TONiC RESM20 angle encoder system installation guide
Legal notices
Copyright
© 2008-2020 Renishaw plc. All rights reserved.
This document may not be copied or reproduced in whole or in part, or transferred to any other media or
language by any means, without the prior written permission of Renishaw.
Trade marks
RENISHAW
®
and the probe symbol are registered trade marks of Renishaw plc. Renishaw product
names, designations and the mark ‘apply innovation’ are trade marks of Renishaw plc or its subsidiaries.
Other brand, product or company names are trade marks of their respective owners.
Patents
Features of Renishaw’s encoder systems and similar products are the subjects of the following patents
and patent applications:
EP0748436 US5861953 EP1173731 US6775008B2 JP4750998
CN100543424C US7659992 JP4932706 CN100507454C US7550710
EP1766335 CN101300463B EP1946048 US7624513B2 JP5017275
CN101310165B US7839296 EP1957943 US6481115 IL138995
EP1094302 CN1293983 GB2397040 JP4813018 US7723639
CN1314511 EP1469969 JP5002559 US2005045586
Disclaimer
WHILE CONSIDERABLE EFFORT WAS MADE TO VERIFY THE ACCURACY OF THIS DOCUMENT
AT PUBLICATION, ALL WARRANTIES, CONDITIONS, REPRESENTATIONS AND LIABILITY,
HOWSOEVER ARISING, ARE EXCLUDED TO THE EXTENT PERMITTED BY LAW.
RENISHAW RESERVES THE RIGHT TO MAKE CHANGES TO THIS DOCUMENT AND TO THE
EQUIPMENT, AND/OR SOFTWARE AND THE SPECIFICATION DESCRIBED HEREIN WITHOUT
OBLIGATION TO PROVIDE NOTICE OF SUCH CHANGES.
Terms and conditions and warranty
Unless you and Renishaw have agreed and signed a separate written agreement, the equipment and/or
software are sold subject to the Renishaw Standard Terms and Conditions supplied with such equipment
and/or software, or available on request from your local Renishaw ofce.
Renishaw warrants its equipment and software for a limited period (as set out in the Standard Terms
and Conditions), provided that they are installed and used exactly as dened in associated Renishaw
documentation. You should consult these Standard Terms and Conditions to nd out the full details of
your warranty.
Equipment and/or software purchased by you from a third-party supplier is subject to separate terms and
conditions supplied with such equipment and/or software. You should contact your third-party supplier for details.
Product compliance
Renishaw plc declares that TONiC complies with the applicable standards and regulations.
A copy of the EU declaration of conformity is available from our website at
www.renishaw.com/productcompliance.
Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The user is cautioned that any changes or modications not expressly approved by Renishaw plc or authorised
representative could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with
the unit to ensure compliance.
Further information
Further information relating to the TONiC encoder range can be found in the TONiC encoder system Data
sheet (Renishaw part no. L-9517-9337). This can be downloaded from our website at www.renishaw.com/
tonicdownloads and is also available from your local representative.
Packaging
Packaging Component Material ISO 11469 Recycling Guidance
Outer box Cardboard Not applicable Recyclable
Polypropylene PP Recyclable
Inserts Low density polyethylene foam LDPE Recyclable
Cardboard Not applicable Recyclable
Bags High density polyethylene bag HDPE Recyclable
Metalised polyethylene PE Recyclable
REACH regulation
Information required by Article 33(1) of Regulation (EC) No. 1907/2006 (“REACH”) relating to products
containing substances of very high concern (SVHCs) is available at www.renishaw.com/REACH.
WEEE recycling guidelines
The use of this symbol on Renishaw products and/or accompanying documentation indicates
that the product should not be mixed with general household waste upon disposal. It is the
responsibility of the end user to dispose of this product at a designated collection point for waste
electrical and electronic equipment (WEEE) to enable reuse or recycling. Correct disposal of
this product will help to save valuable resources and prevent potential negative effects on the
environment. For more information, please contact your local waste disposal service
or Renishaw distributor.
To Next Page
Loading...
Need help?
General
