What to do if no features of my Reverie Indoor Furnishing power base activate?
If no features of your Reverie Indoor Furnishing power base activate, first ensure the remote is paired to the bed. If that doesn't work, check your electrical circuit breaker, as it may have tripped. Also, test the electrical outlet by plugging in another device to ensure the surge protection device isn't defective.
How to fix Reverie Indoor Furnishing remote control that won't activate the bed?
If your Reverie Indoor Furnishing remote control appears operable but won't activate the bed, ensure the power cord is plugged into a working, grounded electrical outlet. It's recommended to use a grounded electrical surge protection device. Test the outlet by plugging in another working appliance.
What to do if head or foot section of Reverie R600 Indoor Furnishing won't return to flat position?
If the head or foot section of your Reverie Indoor Furnishing elevates but doesn't return to the horizontal (flat) position, the power base mechanism may be obstructed. Elevate the power base and check for, and remove, any obstruction. Also, the head section may be too close to the wall, or the headboard may be too close to the edge of the mattress. Ensure there's a 1.5" to 2" distance between the headboard brackets and the mattress; adjust if needed.
How to fix Reverie R600 Indoor Furnishing remote control LED not illuminating?
If the remote control LED of your Reverie Indoor Furnishing does not illuminate, charge the remote using the provided micro USB wall adapter charger.
What to do if Reverie Indoor Furnishing remote showing 'No Bed Paired'?
If your Reverie Indoor Furnishing remote shows “No Bed Paired”, allow the remote to go back to sleep by setting it down and check if it connects after 3 minutes. If the issue persists, repeat the pairing process.
How to reset Reverie R600 Indoor Furnishing after overload condition?
If all functions of your Reverie Indoor Furnishing stopped working due to an overload condition, remove the load and reset the bed by putting it in a flat position, then moving it all the way to the maximum position.
Why does my Reverie Indoor Furnishing Head or Foot Lift function have interference?
If you observe minor interference during the operation of the Head or Foot Lift function of your Reverie Indoor Furnishing, ensure that you are following the duty cycle of the motors (do not operate more than three (3) minutes over a thirty (30) minute period, approximately 10% duty cycle). Also, make sure to press the lift buttons squarely and accurately.
What to do if Pillow Tilt is not performing normally on Reverie R600?
If the Pillow Tilt function of your Reverie Indoor Furnishing is not performing normally, ensure you are pressing the correct button and that the remote has good batteries. Also, check for any obstructions.
How to reduce excessive massage motor noise in Reverie Indoor Furnishing?
If you are experiencing excessive massage motor noise with your Reverie Indoor Furnishing: 1. Place carpet pieces under the bed if it's on hard surface flooring. 2. Elevate the head or foot section slightly to realign the lift/lower mechanisms with the bed support platform. 3. Ensure the bed isn't against a wall, nightstand, or other object. 4. If installed over a bed frame, verify the massage motors aren't causing the frame to vibrate. 5. Confirm the headboard attachment hardware is firmly tightened.
How to recalibrate Reverie R600 remote readout?
If the remote readout of your Reverie Indoor Furnishing doesn’t match the actual bed position, recalibrate it by pressing FLAT on the remote, then lift all sections to the maximum position until it shows 100% on the remote screen.
Important safety instructions, dangers of electric shock, and warnings about burns, fire, or injury.
Warnings about keeping children away from parts and connecting to a properly grounded outlet.
Steps for safely unpacking the power base and assembling the legs.
Solutions for common problems like remote not activating the bed, no features working, or LED not illuminating.
Guidance for issues with head/foot section movement, obstruction, wall proximity, and battery mode operation.
Solutions for 'No Bed Paired' errors, overload issues, minor lift interference, and pillow tilt problems.
Troubleshooting excessive massage motor noise, general base noise, and headboard attachment.
Details of the first year of the limited warranty covering parts and labor for defective components.
Terms for the second through fifth year of the limited warranty, covering parts only.
Coverage for the frame only from year six through twenty, excluding electronics and motors.
General| Brand | Reverie |
|---|---|
| Model | R600 |
| Category | Indoor Furnishing |
| Language | English |
To Next Page
