DOWN FLOW ZERO CLEARANCE
DOWN FLOW ZERO CLEARANCE
PARTS NEEDED FOR THIS CONVERSION REQUIRE ITEMS
FROM THE PARTS BAG
!
DOWN FLOW ZERO CLEARANCE
PARTS NEEDED FOR THIS CONVERSION REQUIRE ITEMS
PARTS BAG, CONVERSION KIT RXGY-CK
DOWN FLOW ZERO CLEARANCE
PARTS NEEDED FOR THIS CONVERSION REQUIRE ITEMS
AND RXGY-ZK
FROM PARTS BAG(PROVIDED W/UNIT)
COUPLING
3
*
"
8
0
-
'
PARTS NEEDED:
FROM PARTS BAG(PROVIDED W/UNIT)
INTAKE
COUPLING
W/ NUT
BULKHEAD
COUPLING
PARTS NEEDED:
FROM PARTS BAG(PROVIDED W/UNIT)
#8 X 1/2"
SCREW
(X2)
HOSE
C
LAMP
PARTS NEEDED:
FROM THE PARTS BAG
YOU MUST HAVE THE OUTLINED PARTS FROM THESE KITS BEFORE PROCEEDING.
!
(X3)
TUBE C
PARTS BAG, CONVERSION KIT RXGY-CK
YOU MUST HAVE THE OUTLINED PARTS FROM THESE KITS BEFORE PROCEEDING.
HOSE -
DOUBLE ELBOW
INTAKE AIR
DIFFUSER
AND RXGY-ZK.
YOU MUST HAVE THE OUTLINED PARTS FROM THESE KITS BEFORE PROCEEDING.
HOSE -
DOUBLE ELBOW
F
ROM CONVERSION KIT RXGY-CK
2-5/8" FLUSH
MOUNT PLUG
#8 X 1/2"
SCREW
(X4)
FROM ZERO-CLEARANCE CONVERSION KIT RXGY-ZK
F
ROM CONVERSION KIT RXGY-CK
1/4" BLACK
VENT TUBING
#8 X 1/2"
SCREW
FROM ZERO-CLEARANCE CONVERSION KIT RXGY-ZK
.559" CONDENSATE
TRAP DRAIN PLUG
5/8" DRAIN
HOSE B
1/2" DRAIN
HOSE E
.559" CONDENSATE
TRAP DRAIN PLUG
CONDENSATE
TRAP BRACKET
(
DOWN FLOW)
O-RING
#8 X 1/2"
SCREW
(X10)
ELECTRIC DRILL
TOOLS/MATERIALS NEEDED:
PIPE
COLLAR/GASKET
ASSEMBLY
(X2)
TOOLS/MATERIALS NEEDED:
3/16" DRILL BIT
INTAKE
PIPE
TOOLS/MATERIALS NEEDED:
TUBING CUTTER
1/4" HEX HEAD DRIVER
5/16 HEX HEAD DRIVER
INTAKE
FLUE PIPE
ASSEMBLY
PVC GLUE AND PRIMER
HAMMER
1/4" HEX HEAD DRIVER
5/16 HEX HEAD DRIVER
W/ O-RING
FLUE PIPE
ASSEMBLY
PVC GLUE AND PRIMER
W/ O-RING
O-RING
1/8" DRILL BIT
1
NOTE: STEPS 1- 4 SHOWN WITH FURNACE IN “AS SHIPPED CONDITION”
NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE
PLIERS
TRANSITION
COUPLING
(RETAIN)
FLUE TRANSITION (DISCARD)
ELBOW “RETAIN”
NOTE: STEPS 1- 4 SHOWN WITH FURNACE IN “AS SHIPPED CONDITION”
NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE
5/16 HEX HEAD DRIVER
TRANSITION
COUPLING
(RETAIN)
FLUE TRANSITION (DISCARD)
ELBOW “RETAIN”
2
2a
NOTE: STEPS 1- 4 SHOWN WITH FURNACE IN “AS SHIPPED CONDITION”
NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE
FLAT HEAD SCREWDRIVER
5/16 HEX HEAD DRIVER
2-5/8"
2a
INSTALL
NOTE: THESE CONVERSION INSTRUCTIONS ARE INTENTIONALLY GENERIC, SOME PARTS MAY BE DIFFERENT IN YOUR FURNACE
FLAT HEAD SCREWDRIVER
2d
1a - REMOVE ELBOW, (2) COUPLINGS, AND FLUE TRANSITION.
(RETAIN ELBOW AND COUPLINGS FOR LATER USE.)
(NOTE: REMOVE COUPLING ON INDUCER WITH ELBOW
FOR EASIER REMOVAL).
1b - REMOVE TRAP AND HOSES. RETAIN HOSE D FOR LATER USE.
(NOTE: TO REMOVE TRAP REMOVE (2) SCREWS AND PULL STRAIGHT OUT).
1a - REMOVE ELBOW, (2) COUPLINGS, AND FLUE TRANSITION.
(RETAIN ELBOW AND COUPLINGS FOR LATER USE.)
(NOTE: REMOVE COUPLING ON INDUCER WITH ELBOW
1b - REMOVE TRAP AND HOSES. RETAIN HOSE D FOR LATER USE.
(NOTE: TO REMOVE TRAP REMOVE (2) SCREWS AND PULL STRAIGHT OUT).
1b - REMOVE TRAP AND HOSES. RETAIN HOSE D FOR LATER USE.
(NOTE: TO REMOVE TRAP REMOVE (2) SCREWS AND PULL STRAIGHT OUT).
2a - INSTALL 2-5/8" FLUSH MOUNT PLUG.
2b - REMOVE LEFT 2-3/8" FLUSH PLUG IN BLOWER SHELF - DISCARD.
2c - RELOCATE RIGHT 2-3/8" FLUSH MOUNT PLUG FROM BLOWER SHELF TO
TOP PLATE.
2d - RELOCATE .403" DRAIN PLUG IN THE COLLECTOR BOX.
2a - INSTALL 2-5/8" FLUSH MOUNT PLUG.
2b - REMOVE LEFT 2-3/8" FLUSH PLUG IN BLOWER SHELF - DISCARD.
2c - RELOCATE RIGHT 2-3/8" FLUSH MOUNT PLUG FROM BLOWER SHELF TO
TOP PLATE.
2d - RELOCATE .403" DRAIN PLUG IN THE COLLECTOR BOX.
DISCARD
2b
2b - REMOVE LEFT 2-3/8" FLUSH PLUG IN BLOWER SHELF - DISCARD.
2c - RELOCATE RIGHT 2-3/8" FLUSH MOUNT PLUG FROM BLOWER SHELF TO
2d - RELOCATE .403" DRAIN PLUG IN THE COLLECTOR BOX.
ST-A1194-31-04
To Next Page
Loading...
Need help?
General