Rice Lake IQ plus 355 - User Manual

December 2004 45774
IQ plus
®
355 Digital Weight Indicator
Analog Output Option
PN 43381
IQ plus 355 Analog Output Module Installation
To install or replace the analog output module, ensure
power to the indicator is disconnected, then place the
indicator face-down on an antistatic work mat. Loosen
all in-use cord grips and remove the screws that hold
the backplate to the enclosure body. Lift the backplate
away from the enclosure and set it aside.
Use a wrist strap to ground yourself and
protect components from electrostatic
discharge (ESD) when working inside
the indicator enclosure.
NOTE:
Ensure jumpers JP1 and JP2 on analog output
board are installed in position 1 (POS1) as shown in
Figure 1.
Mount the analog output module on its standoffs in
the location shown in Figure 1 and plug the module
input into connector J5 on the IQ plus 355 board.
Connect output cable to the analog output module as
shown in Table 1, then reassemble the enclosure as
described on page 2.
Table 1. Analog Output Module Pin Assignments
Figure 1. Analog Output Module Installation on IQ plus 355 Board
Caution
Pin
Signal
1+ Current Out
2– Current Out
3+ Voltage Out
4– Voltage Out
Transformer
BR1
C23
VR1
JMP4
C24
MECCA1
C66
DIGITAL
+5V
TEST
J4
123
4
567
SERIAL COMM & DIGITAL IN
EDPT GND EDPR PRMA PRT IN2 IN1
F2 F1
Blue wire
JP4
ANALOG
GND
ANALOG
+5V
TEST
ANALOG
–5V
TEST
+
+
GND
GND
JP1
JP2
+
VR2
C25
+
VR3
C67
+
–
+
Keypad Connector
J7
EEPROM
A/D Converter
JP7
Brown wire
Microprocessor
X2
LED DRIVER
LED DRIVER
U4
U5
To setup switch
ON OFF
SET/ISP
J1
–EXC
+EXC
–SENSE
+SENSE
–SIG
+SIG
6
5
4
3
2
1
LOAD CELL CONNECTOR
J5
ANALOG OUTPUT
ANALOG OUTPUT
MODULE
JP1
JP2
POS1 POS2
J1
4
3
2
1
POS2 POS1

Summary

IQ plus 355 Analog Output Module Installation

ESD Safety Precautions

Use a wrist strap to protect components from electrostatic discharge (ESD).

Jumpers Installation Note

Ensure jumpers JP1 and JP2 are installed in position 1 (POS1) for the analog output board.

Enclosure Reassembly for IQ plus 355

Analog Output Calibration for IQ plus 355

Calibration Prerequisites

Calibrate analog output after indicator configuration and calibration.

IQ plus 510;710 Analog Output Module Installation

ESD Safety Precautions for 510;710 Series

Use a wrist strap to protect components from electrostatic discharge (ESD).

Jumpers Installation Note for 510;710 Series

Ensure jumpers JP1 and JP2 are installed in position 1 (POS1) for the analog output board.

Enclosure Reassembly for IQ plus 510;710

Analog Output Calibration for IQ plus 510;710

Calibration Prerequisites for 510;710 Series

Calibrate analog output after indicator configuration and calibration.

IQ plus 350 Analog Output Module Installation

ESD Safety Precautions for 350 Series

Use a wrist strap to protect components from electrostatic discharge (ESD).

Jumpers Installation Note for 350 Series

Ensure jumpers JP1 and JP2 are installed in position 1 (POS1) for the analog output board.

Enclosure Reassembly for IQ plus 350

Analog Output Calibration for IQ plus 350

Calibration Prerequisites for 350 Series

Calibrate analog output after indicator configuration and calibration.

Rice Lake IQ plus 355 Specifications

General

Brand	Rice Lake
Model	IQ plus 355
Category	Accessories
Language	English