To Next PageTo Next PageWhy are documents not printing from my Ricoh All in One Printer?
If documents and reports are not printing from your Ricoh All in One Printer, it might be because the paper output tray is full. Remove the prints from the tray. Alternatively, the printer may be out of paper. In this case, load paper into the printer.
Why do misfeeds occur frequently on Ricoh Pro 8120?
Frequent misfeeds in your Ricoh All in One Printer may be caused by the tray's side or end fences not being set properly. Remove the misfed paper, then check that the side or end fences are correctly set and locked.
What to do if an error has occurred on Ricoh Pro 8120?
If an error has occurred on your Ricoh All in One Printer, and a function displays an "Error Occurred" status in the [Check Status] screen, press [Check] for the function with the error. Review the displayed message and take the appropriate action. You can use other functions normally.
Why does the error message remain on Ricoh All in One Printer after removing misfed paper?
If an error message persists on your Ricoh All in One Printer after removing misfed paper, it might be because the front cover needs to be fully opened and closed. Do this after removing the jammed paper. Alternatively, paper may still be jammed in the tray.
What to do if Ricoh All in One Printer misfeeds frequently?
If your Ricoh All in One Printer frequently misfeeds, it could be due to using curled paper, which can cause misfeeds and soiled edges. Straighten the paper to remove stiffness. Load the paper upside down with curled edges facing downward. Lay cut paper on a flat surface to prevent curling, and do not lean it against the wall.
What to do if an error message remains displayed even if the indicated cover is closed on Ricoh Pro 8120 All in One Printer?
If an error message remains displayed on your Ricoh All in One Printer even after closing the indicated cover, it means that one or more other covers are still open. Close all the covers of the machine.
What to do if Ricoh Pro 8120 is unable to connect to the network?
If your Ricoh All in One Printer can't connect to the network, it might be due to a network error. Ensure the printer is correctly connected and properly configured. If issues persist, contact your administrator. If the indicator lamp remains lit after troubleshooting, contact your service representative.
Why is the display turned off on my Ricoh Pro 8120?
If the display on your Ricoh All in One Printer is turned off, the machine may be in Low Power mode. Touch the display panel or press a key on the control panel to exit Low Power mode.
How to turn on the display on Ricoh Pro 8120?
If the display is off on your Ricoh All in One Printer, the machine could be in Sleep mode. Press the [Energy Saver] key or the [Check Status] key to exit Sleep mode.
What to do if nothing happens when pressing [Check Status] or [Energy Saver] key on Ricoh Pro 8120?
If nothing happens when you press the [Check Status] key or the [Energy Saver] key on your Ricoh All in One Printer, the power might be turned off. Ensure the main power indicator is off, and then turn on the power.
General| Print Speed (Black) | Up to 120 ppm |
|---|---|
| Print Resolution | 1200 x 1200 dpi |
| Dimensions | 1, 020 x 1, 020 x 1, 250 mm |
| Weight | Approx. 130 kg |
| Maximum Paper Size | A3 |
| Duplex Printing | Yes |
| Memory | 4 GB |
| Operating System Compatibility | Windows, macOS, Linux |
| Connectivity | Ethernet, USB |
| Supported Media Sizes | A3, A4, A5, B4, B5 |
| Warm-up Time | Less than 30 seconds |
| First Print Speed | 4.5 seconds |
| Supported Paper Weights | 52-300 gsm |
| Network Connectivity | Ethernet 10 base-T/100 base-TX/1000 base-T |
