What to do if J099 appears on Ricoh PRO C7200X (Main Machine Tray)?
The J099 error on your Ricoh Printer's main machine tray can occur if coated or unsupported paper is loaded. To resolve this, load supported paper in the wide LCT or another paper tray that supports the paper. Additionally, if sheets are stuck together, fan the paper before loading it to loosen them.
Why does my Ricoh PRO C7200X have wrong detection of double feeding?
If the Ricoh Printer detects double feeding when using thin paper (52.3 to 63.0g/m2), set the [Double Feed Detection] to OFF. If the Double-Feed Sensor is dirty with paper powder, clean it using a blower brush.
What causes J080 to appear on Ricoh PRO C7200X (Paper Delay in Specific Papers)?
J080 appears on the Ricoh Printer when the paper position goes over the calibration threshold because the sub-scan registration position is calibrated by accelerating/decelerating the line speed of transfer timing roller. You can set No. 1331-01 "Jam Detection: Detect JAM080" in “Custom Paper Settings (IMSS)” to [0] (Off). Note that the leading edge in the image may shift if this switch is off.
How to troubleshoot paper skew on a Ricoh Printer?
To address paper skew with your Ricoh Printer, ensure the side fence setting is correct. If the skew level of output is not permissible, lowering the SP1-116-001 to 14 (Skew Detection Level) makes the skew detection level stricter. Also, check for and remove any foreign materials in the paper feed path and adjust the Rotary Gate Position. Adjust the Rotary Gate Position for Incorrect paper arching degree (Inappropriate registration buckle) and Incorrect parallelism.
How to resolve jams related to duplex/invert in short grain and thickest paper on Ricoh PRO C7200X?
To address jams related to duplex/invert in short grain and thickest paper on your Ricoh Printer, clean the transfer rollers around the locations where jam occurs. The jams are caused by an insufficient force of transferring thick papers.
What to do for no feeding (poor-quality paper) in Ricoh PRO C7200X Printer?
To prevent no feeding (poor-quality paper) in the main machine paper feed of the Ricoh Printer, increase the separation pressure.
How to fix jams related to insufficient separation on thin paper in Ricoh PRO C7200X?
To address jams related to insufficient separation on thin paper in your Ricoh Printer, if the mask width of paper leading edge can be widened, or the erase margin of trailing edge can be widened. This is because a lack of margin on the paper leading edge allows the separation plate on fusing roller to catch the paper, which produces an accordion-like jam. Also, a lack of margin on the trailing edge of paper also allows the separation plate on pressurizing side to catch the paper in duplex printing.
How do I resolve roller marks on the buffer pass unit of my Ricoh Printer?
To address roller marks on the buffer pass unit of your Ricoh Printer, select 'Magazine' for the booklet printing method and set the binding margin to 5mm or greater. This issue arises because the temperature on the surface of toner differs between the contact area of the paper transport roller and the image, and other non-contact areas.
How to fix frequent paper misfeeds in my Ricoh PRO C7200X?
Frequent paper misfeeds in the Ricoh Printer may occur if coated or unsupported paper is loaded in the tray. Try loading paper supported by the machine's paper tray in the wide LCT or another paper tray. Also, ensure the side fences match the paper width, the paper size/orientation/type is specified correctly in tray paper settings, and the paper tray isn't overloaded. Flatten curled or wavy sheets, protect unused sheets from moisture, enable the Pickup Assist setting, and clean the paper feed sensor and transport roller if they're stained with paper dust or toner. If the transfer timing motor isn't operating correctly, check for any loose/disconnected harnesses. Check that the encoder is correctly attached to the transfer timing roller. Check for anything which is exerting load on the tra...
Explains the function of SC codes displayed on the machine when errors occur.
Provides a step-by-step procedure for responding to SC codes and contacting service.
Categorizes and describes image quality issues related to lines and streaks appearing on prints.
Details various types of spots, their causes, and solutions for image quality problems.
Describes and provides solutions for horizontal black streaks appearing at the image edge.
Explains how to resolve horizontal white streaks that appear perpendicular to the paper feed direction.
Details troubleshooting steps for vertical black streaks appearing on halftone images.
Provides solutions for black or colored spots appearing on prints at regular intervals.
Covers troubleshooting for white spots and toner scattered around solid fill prints.
Explains how to fix faintness at the leading edge of prints due to transfer issues.
Provides solutions for faintness appearing at the trailing edge of prints, often related to paper weight.
General| Print Speed (Black) | 75 ppm |
|---|---|
| Paper Capacity | 8, 250 sheets |
| Color Management | Yes |
| Duplex Printing | Yes |
| Print Technology | Laser |
| Print Speed | 75 ppm |
| Maximum Paper Size | 13 x 19.2 inch |
| Connectivity | Ethernet |
| Warm-up Time | 36 seconds |
| First Print Speed | 7.2 seconds |
| First Print Out Time | 7.2 seconds |
| Paper Weight | 52 gsm |
| Supported Media Types | Coated paper |
| Memory | 4 GB |
| Network Connectivity | Ethernet |
| Operating System Compatibility | Windows |
| Media Sizes | A3, A4, A5, B4, B5, Legal, Letter, Executive, Custom sizes |
| Supported Media Sizes | A3, A4, A5, B4, B5, Legal, Letter, Executive, Custom sizes |
| Weight | 440 lbs (200 kg) |
To Next Page
