Why is there a blot of ink on the shirt from Ricoh Ri 2000 Printer?
A blot of ink on the shirt could be due to: * The frame blotting with ink. Clean the frame. * The print head rubbing against the media during printing. Change the [HEIGHT SETTING], and then perform HEIGHT ADJUST again.
Why do dark shirt prints look dull with my Ricoh Ri 2000 Printer?
If your Ricoh Printer's dark shirt prints look dull, ensure the white nozzles are near 100% and that you're pretreating the shirt adequately by increasing the amount of pretreat being sprayed.
Why does my Ricoh Printer make light shirts look dull?
If your Ricoh Printer light shirt prints look too dull and the nozzle is 100%, the wrong output profile may be selected. If printing in 600 X 600 DPI and using a profile meant for 1200 X 1200 DPI, change the profile.
How to fix multiple missing nozzles on my Ricoh Ri 2000?
If several nozzles are out on your Ricoh Printer and head cleaning doesn't improve it, let the printer sit overnight to allow any air introduced during ink fill or cleaning to settle.
Why does my Ricoh Printer cartridge read 0%?
A temporary communication loss may have caused the cartridge reading error. Remove the cartridge that reads 0%. The status should change to NC, and a message indicating cartridges are not loaded will appear. Reinsert the cartridge; the percentage reading should return to normal. If it still reads 0%, turn the printer off and then on again.
How to fix fuzzy blurry prints on Ricoh Ri 2000 Printer?
Fuzzy or blurry prints can occur due to several reasons. Check the following: * The table height might be too low. Set the garment correctly on the platen, and then perform HEIGHT ADJUST again. * Too much ink (oversaturation) may cause bleeding. Check the settings in ColorGATE Productionserver, ensuring the rendering intent is set to perceptual and that profile selections haven't been altered. * Nozzle deflection. Perform normal or strong nozzle cleaning, then recheck the nozzles. * Poor pretreat on dark shirts with a white underbase. Check the dilution ratio of the pretreatment and the coating/drying method again. * Head alignment may be off. Perform the head alignment procedure.
Why does my Ricoh Printer cartridge read 0% suddenly?
If your Ricoh Printer cartridge reads 0% after showing a high percentage, it may be a temporary communication loss. Remove the cartridge, wait for the 'NC' status and a message indicating cartridges are not loaded, then reinsert it. If it still reads 0%, turn the printer off and back on.
Why is the white concentration light on my Ricoh Ri 2000?
A light white concentration is often caused by insufficient agitation of white ink cartridges. Agitate the cartridge additionally. After that, perform ‘strong’ head cleaning 3-4 times.
What to do if Ricoh Ri 2000 print looks too dull?
If your print looks too dull, and the nozzle is at 100%, the wrong output profile might be selected. If printing in 600 X 600 dpi and using a profile meant for 1200 X 1200 dpi, change the profile.
What causes Ricoh Ri 2000 color print to appear shifted from white Underbase print?
A shifted color print from the white underbase can be caused by: * Table height being too low. Set the garment correctly on the platen, and then perform HEIGHT ADJUST again. * Head alignment being off. Perform the head alignment procedure. * Misalignment of print positions for white and color. Adjust the print position for white and color. * The material of the shirt and the amount of ink ejected. Input the amount of “Choke” with ColorGATE Productionserver.
General| Print Technology | Inkjet |
|---|---|
| Ink Type | Pigment Ink |
| Connectivity | USB, Ethernet |
| Operating System Compatibility | Windows |
| Weight | 250 lbs |
| Printhead | Ricoh |
| Print Resolution | 1200 x 1200 dpi |
| Substrate Compatibility | Cotton, Polyester, Blends |
| Power Requirements | AC 100-240V, 50/60 Hz |
To Next Page
