RIDGID RP 210 User Manual (English)

Other manuals for RIDGID RP 210

Operator's Manual14 pages

User Manual14 pages

Questions and Answers:

K
Kaylee IngramAug 13, 2025
Why won't my RIDGID RP 210 turn on?
- C
  Cody MendozaAug 13, 2025
  If your RIDGID Power Tool won't turn on when you press the ON/OFF button, it might be due to several reasons: * The battery may be completely discharged or faulty. Try inserting a fully charged battery or recharging the dead one. * The battery might not be correctly inserted. Ensure it's fully inserted into the tool's handle. * The battery level could be too low. Replace it with a fully charged battery or recharge the current one. * The tool or battery might be too cold or hot. Allow the tool to sit in a room with a temperature between 0°F (-20°C) to 140°F (60°C) to reach the correct operating range.
K
Kimberly DavisAug 16, 2025
How to fix incomplete pressed connections with RIDGID RP 210 Power Tool?
- A
  Andrea HolmesAug 16, 2025
  If your RIDGID Power Tool is not producing complete pressed connections, ensure that you are using the correct jaws for the tube size and material. Also, make sure the tool is square to the tube and that the jaw contour is aligned with the fitting contour.
C
Chad NguyenAug 20, 2025
What to do if the yellow LED glows continuously on my RIDGID Power Tool?
- J
  Jose RussoAug 20, 2025
  If the yellow LED on your RIDGID Power Tool glows continuously and the tool doesn't start the press cycle when you press the trigger, it could be that the attachment mounting pin is not fully closed. Ensure the attachment mounting pin is inserted to the fully closed position.
N
Noah AriasAug 25, 2025
What to do if RIDGID RP 210 Power Tool jaws are locked onto fitting?
- B
  Bradley LongAug 25, 2025
  If the jaws of your RIDGID Power Tool are locked onto the fitting, it may be because the press was not successfully completed. Inspect and repress the fitting.
G
George BirdAug 27, 2025
What does it mean when the red LED blinks on my RIDGID Power Tool?
- M
  Mr. Brent GoodwinAug 27, 2025
  If the red LED on your RIDGID Power Tool blinks repeatedly and the tool won't start the press cycle when you press the trigger, it indicates a tool malfunction. Push the pressure release valve to remove the jaws from the fitting.
J
James BurnsAug 31, 2025
Why won't my RIDGID Power Tool run when I press the trigger?
- D
  delgadojoseAug 31, 2025
  If your RIDGID Power Tool won't run when you depress the trigger, it is possible that the tool is locked and needs servicing. Contact Ridge Tool Technical Service Department at (800) 519-3456 for the nearest Authorized Service outlet.
R
Ryan BentleySep 4, 2025
What to do if the yellow LED glows continuously and the RIDGID RP 210 won't start when pressing the trigger?
- C
  Charles MedinaSep 4, 2025
  If the yellow LED is continuously glowing and the RIDGID Power Tool doesn't start, several issues could be the cause. First, ensure the attachment mounting pin is fully closed. Then, remove and reinsert the fully charged battery. If the press was unsuccessful, repress the fitting. Make sure you are using the correct jaws for the tube size and material and that the tool is square to the tube, with the jaw contour aligned with the fitting contour. Keep in mind that scheduled maintenance/recalibration is mandatory after 32,000 presses, or the tool may be 'locked' and require servicing.
N
ncallahanSep 8, 2025
What to do if the red LED blinks repeatedly and the RIDGID Power Tool won't start?
- A
  andrew60Sep 8, 2025
  If the red LED blinks repeatedly and the RIDGID Power Tool doesn't start, make sure the attachment mounting pin is fully engaged. Also, the tool may be out of the operational temperature range of 15°F (-10°C) to 122°F (50°C).

RIDGID RP 210 Specifications

General

Battery	18V Lithium-Ion
Max Pressure	12, 000 psi
Hydraulic Ram Output	12, 000 psi
Handle Type	Pistol Grip
Capacity (Copper/Steel)	1/2" – 1 1/4" (12 – 32 mm)
Capacity (PEX)	3/8" – 1 1/2" (10 – 38 mm)
Operating Temperature Range	15°F to 122°F (-9°C to 50°C)
Capacity	1/2" – 1 1/4" (Copper/Steel), 3/8" – 1 1/2" (PEX)