Rigol DS1104B User Manual (English)

Other manuals for Rigol DS1104B

User Guide172 pages

Programming Guide152 pages

Service Guide75 pages

Quick Guide16 pages

Questions and Answers:

B
barrettdeniseAug 3, 2025
What to do if my Rigol Test Equipment oscilloscope doesn't display any waveform after pressing the RUN/STOP button?
- F
  frenchdavidAug 3, 2025
  If your Rigol Test Equipment oscilloscope isn't showing a waveform after you press RUN/STOP, here's what to check: * See if the Trigger Mode is set to “Normal” or “Single” and whether the trigger level is outside the signal range. If the trigger level is out of range, adjust it using the knob or by pressing the 50% button. * Alternatively, set the Trigger Mode to “AUTO”. * You can also push the AUTO button to attempt to automatically display the waveform.
A
Andre BarronAug 7, 2025
How to fix a dark screen on my Rigol Test Equipment oscilloscope after powering it on?
- S
  Samuel OwensAug 8, 2025
  If your Rigol Test Equipment oscilloscope screen remains dark after powering on, try these steps: * First, check the power cord connection to ensure it's secure. * Next, verify that the power switch is turned on. * If both are fine, restart the oscilloscope. If the problem persists after these steps, further assistance may be needed.
C
changalexandraAug 12, 2025
Why doesn't a waveform appear on my Rigol DS1104B after signal acquisition?
- K
  Kevin EllisonAug 12, 2025
  If a waveform doesn't appear on your Rigol Test Equipment after signal acquisition, consider the following checks: * Ensure the probes are correctly connected to the signals and firmly attached to the channels. * Also, verify that the probes are properly connected to the object being tested and that the circuit generates a signal at the test point. * Finally, try repeating the acquisition.
K
kevansAug 17, 2025
How to get a stable waveform display on Rigol Test Equipment oscilloscope?
- M
  Mark ShawAug 17, 2025
  To achieve a stable waveform display on your Rigol Test Equipment oscilloscope, consider these adjustments: * Check that the Trigger Source is set to the channel you are using. * Verify the Trigger Type: use “Edge” for normal signals and “Video” for VIDEO signals. * Try switching the coupling to HF Rejection or LF Rejection to filter out noise that might be disturbing the trigger. * Adjust the trigger Sensitivity and the hold off time.
E
Elizabeth DavisAug 20, 2025
What causes incorrect measurement results on Rigol DS1104B Test Equipment (10x higher or lower)?
- B
  Benjamin HartmanAug 20, 2025
  If the measurement result on your Rigol Test Equipment is significantly off (10 times higher or lower than expected), the most likely cause is a mismatch between the probe attenuation and the channel attenuation. Check if the probe attenuation setting matches the channel attenuation setting.
J
Juan SmithAug 26, 2025
How do I resolve a ladder-like waveform display on my Rigol DS1104B Test Equipment oscilloscope?
- L
  Lisa AtkinsAug 26, 2025
  If your Rigol Test Equipment oscilloscope displays a signal as a ladder-like waveform: * The time base setting may be too slow. Turn the horizontal knob to increase the horizontal resolution. * Alternatively, the display Type might be set to “Vectors”. Set it to “Dots” mode to improve the display.
T
Tracy CortezAug 29, 2025
Why can't my Rigol DS1104B connect to a PC or PictBridge printer via USB?
- B
  Benjamin VillaAug 29, 2025
  If your Rigol Test Equipment is unable to connect to a PC or PictBridge printer via USB: * When connecting to a PC, if you see an “Unknown device” message or a prompt indicating a scanner or camera was found, go to the Utility menu, choose I/O Setting, and check the USB Device menu. If it's set to “PictBridge”, switch it to “Auto Detect” or “Computer”. * If connecting to a PictBridge printer is unsuccessful, switch the USB Device menu to “Auto Detect” or “PictBridge”. In either case, restarting the oscilloscope may be necessary.

Rigol DS1104B Specifications

General

Bandwidth	100 MHz
Channels	4
Sample Rate	1 GSa/s
Input Voltage Range	400V (DC + AC Peak)
Vertical Sensitivity	2 mV/div to 10 V/div
Timebase Range	5 ns/div to 50 s/div
Display Resolution	800 x 480
Trigger Modes	Edge, Pulse, Video, Slope, Alternate
Vertical Resolution	8 bits
Interfaces	USB Host, USB Device
Input Impedance	1 MΩ ± 2%
Memory Depth	16 kpts
Display	7-inch TFT LCD (800x480)