To Next PageTo Next PageWhat does error 07 mean on my Rinnai Zen I24 Boiler?
If Error 07 appears on your Rinnai Boiler, it indicates continuous use of domestic hot water for more than 8 hours. Stop using domestic hot water and press the DHW button to reactivate the function. If no one is using hot water, a breakage of the hydraulic pipeline is possible, so call a technician.
What to do if I smell gas coming from my Rinnai Zen I24?
If you smell gas, immediately stop the Rinnai Boiler and gas supply. Open all windows and doors to ventilate the area. Do not operate any appliances to prevent potential explosions. Contact your gas supplier and regularly inspect the gas pipes and shut-off valve for leaks.
Why does my Rinnai Zen I24 have ignition failure?
If your Rinnai Boiler fails to ignite, there are several potential causes: 1. Check if the boiler is properly plugged into an outlet with the correct voltage. 2. Ensure the set temperature on the display is higher than the current temperature. 3. If error code 11 is displayed, turn the boiler off and then on again. 4. Verify that the gas supply valve is open, ensuring gas is available to the boiler.
Why is there no hot water coming from my Rinnai Zen I24 Boiler?
If there is no hot water from your Rinnai Boiler, consider these possible causes: * Ensure the DHW (Domestic Hot Water) mode is active by pressing the DHW button on the remote control. * Confirm there is a water supply to the boiler and wait for water availability. * Check that the water pressure is not too low, as the boiler requires a minimum flow rate of 2.3 liters per minute to start. * Make sure the cold water supply valve is fully open.
What to do if I smell exhaust gas from my Rinnai Boiler?
If you smell exhaust gas from your Rinnai Boiler, immediately stop the boiler and contact Rinnai service or maintenance for assistance.
How to troubleshoot if my Rinnai Zen I24 Boiler is not heating the room enough?
If the room isn't heating adequately with your Rinnai Boiler, consider the following: 1. Ensure the CH (Central Heating) mode is activated on the remote control. 2. Increase the set heating temperature. 3. Adjust or disable reservation/outgoing mode. 4. Reduce or stop domestic hot water usage. 5. Open any closed heating valves. 6. Connect the remote controller and adjust CH settings. 7. Clean the CH return filter. 8. Remove air from the pipes by opening the manual air drain point.
What does error 34 mean on my Rinnai Boiler?
If Error 34 appears on your Rinnai Boiler, it indicates a hot water thermistor failure. Press the DHW button twice to deactivate and reactivate the function. If the code reappears, contact Rinnai technical assistance.
What does error 11 mean on my Rinnai Zen I24?
If Error 11 is displayed on your Rinnai Boiler, it means the burner flame was not detected. Verify that the gas safety valve is open and press the CH button twice to deactivate and reactivate the heating function.
What does error 61 mean on my Rinnai Zen I24?
If your Rinnai Boiler displays Error 61, it signals a combustion fan failure. Verify that the exhaust system is not obstructed. Turn the boiler off and on; if the error code persists, contact Rinnai technical assistance.
What does error 16 mean on my Rinnai Zen I24 Boiler?
If your Rinnai Boiler displays Error 16, it indicates CH overheating. Ensure at least one thermostatic valve is open, vent the air in the heating circuit, and clean the return line filter of the CH.
General| Model | Zen I24 |
|---|---|
| Heating Capacity | 24kW |
| Weight | 32 kg |
| Boiler Type | Combi |
| ErP Heating Efficiency Class | A |
| ErP Water Heating Efficiency Class | A |
| CH Energy Efficiency (%) | 94% |
| NOx Class | 5 |
| Fuel Type | Natural Gas |
