Ritmo BASIC 160 V1 - Operating Instructions (Continued); Temperature Setpoint Modification; Changing Temperature Measure System; Error Messages and Handling

4. OPERATING INSTRUCTIONS ﻞﻴﻐﺸﺘﻟا تﺎﻤﻴﻠﻌﺗ
4./7
Temperature setpoint modification:
ةراﺮﺤﻟا ﺔﺟرد داﺪﻋإ ﺔﻄﻘﻧ ﻞﻳﺪﻌﺗ:
• حﺎﺘﻔﻤﻟا ﻰﻠﻋ راﺮﻤﺘﺳﻻا ﻊﻣ ﻂﻐﺿاC ةﺪﻤﻟ 4 ﺗ ﻰﺘﺣ ﺎًﺒﻳﺮﻘﺗ ﻲﻧاﻮﺛﺾﻴﻣﻮﻟا ﻲﻓ ﺔﺿوﺮﻌﻤﻟا ﺔﻤﻴﻘﻟا أﺪﺒ.
• Keep C pressed for approximately 4 seconds until the value displayed starts blinking.
• ﻰﻠﻋ ﻂﻐﺿاC وB ﺔﺑﻮﻠﻄﻤﻟا ﺔﻤﻴﻘﻟا داﺪﻋﻹ .
• Press C and B to set the desired value.
• ٍن ا ﻮ ﺛ ﻊﻀﺑ ﺮﻈﺘﻧاو ﻦﻴﺣﺎﺘﻔﻤﻟا رﺮﺣ .ﻮﻟا ﻦﻋ ةﺪﻌﻤﻟا ﺔﻤﻴﻘﻟا ﻒﻗﻮﺘﺗةﺮآاﺬﻟا ﻲﻓ
ﺎﻬﻈﻔﺣ ﻢﺘﻳو ﺾﻴﻣ .
• Release both keys and wait for a few seconds. The value set halts to blink and is memorized.
How to change the temperature measure system:
ةراﺮﺤﻟا ﺔﺟرد سﺎﻴﻗ مﺎﻈﻧ ﺮﻴﻴﻐﺗ ﺔﻴﻔﻴآ:
• حﺎﺘﻔﻤﻟا ﻰﻠﻋ ﻂﻐﻀﻟا ﻲﻓ ﺮﻤﺘﺳاBﻄﻟا ﺲﺒﻘﻣ ﻞﻴﺻﻮﺘﺑ ﻢﻗ ﻢﺛ ،ﺔﻗﺎ .
• Keep B pressed, and only then connect the power plug.
• ﺔﻤﻴﻘﻟا ﻂﺒﻀﺑ ﻢﻗ"002 " حﺎﺘﻔﻤﻟا ماﺪﺨﺘﺳا ﻖﻳﺮﻃ ﻦﻋC وB ) ﺪﻌﺑ ﺾﻴﻣﻮﻟا ﻲﻓ مﺪﺨﺘﺴﻤﻟا سﺎﻴﻘﻟا مﺎﻈﻧ أﺪﺒﻴﺳ4 ﺎًﺒﻳﺮﻘﺗ ﻲﻧاﻮﺛ.(
• Set value “002” by using C and B (the measure system in use will start blinking after approximately 4 seconds).
• حﺎﺘﻔﻤﻟا ﻰﻠﻋ ﻂﻐﺿاC وB ةراﺮﺤﻟا ﺔﺟرد سﺎﻴﻗ مﺎﻈﻧ ﺮﻴﻴﻐﺘﻟ) ﺖﻳﺎﻬﻧﺮﻬﻓ ]F [- ﺔﻳﻮﺌﻣ ﺔﺟرد ]C .([ ﻲﻓ ﺎﻬﻈﻔﺣ ﻢﺘﻴﺳو ﺾﻴﻣﻮﻟا ﻦﻋ نﻵا ﺎهداﺪﻋإ ﻢﺗ ﻲﺘﻟا ﺔﻤﻴﻘﻟا ﻒﻗﻮﺘﺘﺳ
ةﺮآاﺬﻟا.
•
Press C and B to change the temperature measure system (Fahrenheit [ F ] – Celsius [ °C]). The value now set will halt
to blink and will be memorized.
Error messages:
ﺄﻄﺨﻟا ﻞﺋﺎﺳر:
ﻪﻠﻴﻐﺸﺗ ةدﺎﻋإ ﻢﺛ يراﺮﺤﻟا ﻢﻈﻨﻤﻟا ﻞﻴﻐﺸﺗ فﺎﻘﻳإ لوﺎﺤﻓ ،ﺔﻴﻟﺎﺘﻟا ﻞﺋﺎﺳﺮﻟا ﻦﻣ يأ تﺮﻬﻇ اذإ .ﺔﻠﻜﺸﻤﻟا تﺮﻤﺘﺳا اذإ ﺪﻤﺘﻌﻤﻟا ﺔﻣﺪﺨﻟا ﺰآﺮﻤﺑ ﻞﺼﺗا .
If one of the following messages appears, try turning off - turning on the thermoregulator. Contact an authorized service centre
if the problem persists.
OP حﻮﺘﻔﻣ ﺲﺠﻣ: ﺎًﻔﻟﺎﺗ نﻮﻜﻳ ﺪﻗ ؛ةراﺮﺤﻟا ﺔﺟرد ﺲﺠﻣ ﻲﻓ ﺔﻠﻜﺸﻣ دﻮﺟو ﻰﻟإ ﺮﻴﺸﺗ .
OP Open Probe: Indicates a problem with the temperature probe; it could be damaged.
OC ةﺮﻄﻴﺴﻟا ﻦﻋ جرﺎﺧ
: يراﺮﺤﻟا ﻢﻈﻨﻤﻟا ﻰﻠﻋ رﺬﻌﺘﻳ ؛ةراﺮﺤﻟا ﺔﺟرد ﻂﺒﺿ ﻲﻓ ﺔﻠﻜﺸﻣ دﻮﺟو ﻰﻟإ ﺮﻴﺸﺗ
ةﺪﻌﻤﻟا ةراﺮﺤﻟا ﺔﺟرد ﻂﺒﺿ.
OC Out of Control: Indicates a problem with the temperature adjustment; the thermoregulator cannot
adjust the temperature set.
Shutdown instructions:
ﻞﻴﻐﺸﺘﻟا فﺎﻘﻳإ تﺎﻤﻴﻠﻌﺗ:
حﺎﺘﻔﻤﻟا ﻰﻠﻋ راﺮﻤﺘﺳﻻا ﻊﻣ ﻂﻐﺿا ،ﻦﻴﺨﺴﺘﻟا حﻮﻟ ﻞﻴﻐﺸﺗ فﺎﻘﻳﻹB ﺔﻤﻠآ ﺮﻬﻈﺗ نأ ﻰﻟإOFF )ﻞﻴﻐﺸﺘﻟا فﺎﻘﻳإ(.
To turn off the heating plate, keep B pressed until the word OFF shows up.
ﺔﻗﺎﻄﻟا ﺲﺒﻘﻣ ﻞﺼﻓا ،يراﺮﺤﻟا ﻢﻈﻨﻤﻟا ﻞﻴﻐﺸﺗ فﺎﻘﻳﻹ.
To turn off the thermoregulator, disconnect the power plug.